Results 121 to 130 of about 424,832 (299)

Numerical analysis of the influence of boundary conditions on the distribution of pore pressures under the Nechranice dam body [PDF]

, 2019
Cílem této práce je pomocí numerického modelování provést analýzu vlivu okrajových podmínek na rozložení pórových tlaků pod tělesem hráze vodního díla Nechranice (dále jen VD Nechranice). Práce obsahuje 4 stručné rešeršní části.
Anna Kutnarová
core  

Pain and Patient‐Reported Physical Function Did Not Differ Among Body Composition Profiles in Patients With Hip Osteoarthritis

Arthritis Care &Research, EarlyView.
Objective To explore whether higher body fat and lower lean mass are associated with greater pain and worse patient‐reported physical function in individuals with hip osteoarthritis (OA). A secondary aim was to examine whether pain and patient‐reported physical function differ according to four body composition profiles: high body fat, low lean mass ...
Alexandra Ryan, Boliang Wang, Fiona Dobson, Ben Kirk, Travis Haber, Kim L. Bennell, Shirley P. Yu, Kim Allison, Ricardo J. S. Costa, Gabrielle Knox, Michelle Hall   +10 more
wiley   +1 more source

Catalogue of analytical solutions for consolidation of unsaturated soils subjected to various initial conditions and time-dependent loadings [PDF]

, 2016
University of Technology Sydney. Faculty of Engineering and Information Technology.Soil consolidation has been a primary geotechnical interest for decades.
Ho, Huu Liem
core  

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

Evaluation of pore structural stability of mesoporous titanium silicates [PDF]

, 2008
Therefore one of the purposes of the work presented here is to complement the stability features by studying the hydrothermal resistance of the Ti-MCM-41 materials prepared by the same procedure.
Carrott, Manuela, Carrott, Peter, Galacho, Cristina   +2 more
core  

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Evaluation of Excess Pore Water Pressure Build-up During Cyclic Triaxial Tests on a Non-plastic Silt

Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2018
Cyclicloading is responsible for pore water pressure buildup, which may later cause liquefactionand surface settlements. Recent studies emphasize that as the pore waterpressure equalizes to initial confining stress, cyclic stress ratio andrelative ...
Eyyüb Karakan, Nazar Tanrınian, Alper Sezer   +2 more
doaj  

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source