Results 61 to 70 of about 726,640 (252)

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar   +3 more
wiley   +1 more source

MICROSTRUCTURES AND PHYSICAL PROPERTIES OF BIOMORPHIC SISIC CERAMICS MANUFACTURED VIA LSI-TECHNIQUE [PDF]

open access: yes, 2012
Biomorphic SiSiC ceramic composites were produced by liquid silicon infiltration (LSI) process. These materials are based on activated coal (ACBC) and wood fibers (MDF).
Raouf Jemmali   +7 more
core   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

open access: yesAdvanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon   +3 more
wiley   +1 more source

Mechanical and dielectric properties of porous and wave-transparent Si3N4-Si3N4 composite ceramics fabricated by 3D printing combined with chemical vapor infiltration

open access: yesJournal of Advanced Ceramics, 2019
Porous Si3N4-Si3N4 composite ceramics were fabricated by 3D printing combined with low-pressure chemical vapor infiltration (CVI). This technique could effectively improve the designability of porous Si3N4 ceramics and optimize the mechanical and ...
Zanlin Cheng   +7 more
doaj   +1 more source

Microstructural Evolution and In Situ Formation of TiB and TiC in Ti─5Al─2.5Sn Alloy Processed by Powder Metallurgy

open access: yesAdvanced Engineering Materials, EarlyView.
Accelerated in situ formation of TiB and TiC in Ti–5Al–2.5Sn–B4C is driven by transient liquid phase formation, which enhances particle reactions and microstructural evolution. This process increases hardness and establishes a coupled relationship between sintering temperature and reinforcement content, strongly influencing porosity in the resulting ...
Fernando. Y. Kojima, Juliano. Soyama
wiley   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

open access: yesAdvanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi   +3 more
wiley   +1 more source

Gyroid Structured Globugraphite Carbon Foam With Hierarchical and Tailored Pore Size

open access: yesAdvanced Engineering Materials, EarlyView.
Secondary sacrificial templates were designed and printed to create a defined network within a porous carbon. Lattices thermally degrades during the sintering process. Lattices are imprinted into the ceramic template and transferred to the morphology of Globugraphite.
Christiane Roller   +6 more
wiley   +1 more source

Adjusting Nucleation Chemistry for the Atomic Layer Deposition of Antimony Selenide on Metal Oxide Surfaces

open access: yesAdvanced Engineering Materials, EarlyView.
The ALD precursor bis(trimethylsilyl)selenide is simultaneously a substrate surface inhibitor. It allows for the growth of Sb2Se3 in combination with tris(dimethylamido)antimony, but also silylates surface hydroxyl groups on the substrate if such hydroxyls are present.
Pei‐Chun Liao   +9 more
wiley   +1 more source

Water purification using porous ceramics prepared by recycling volcanic ash and waste glass

open access: yesApplied Water Science, 2017
Water purification was examined using porous ceramics prepared by sintering a powder mixture of volcanic ash, waste glass and a small amount of wood charcoal.
Tomohiro Ando   +4 more
doaj   +1 more source

Porous alumina-spinel ceramics for high temperature applications

open access: yes, 2011
In order to reduce energy costs, high-temperature insulation porous refractory ceramics have been subjected to increasing demands. Among the techniques used to produce these materials (such as the addition of foaming agents and organic compounds), the ...
Victor C. Pandolfelli   +5 more
core   +1 more source

Home - About - Disclaimer - Privacy