Results 161 to 170 of about 918,872 (308)
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy
Advanced Engineering Materials, EarlyView.A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal +4 more
wiley +1 more source
The paper studies the influence of the content of aluminum nitride nanoparticles on the structure and mechanical properties of the ZK51A magnesium alloy. The microstructure investigations with optical and electron microscopy show that 1 wt.% AlN promotes
Alexander B. Vorozhtsov +4 more
core +1 more source
Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)
Advanced Engineering Materials, EarlyView.Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho +8 more
wiley +1 more source
Effects of Post-Heat Treatment on Mechanical and Tribological Properties of 3D-Printed PLA and PEEK Structures. [PDF]
Polymers (Basel)Deng Y, Chang L.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.This study reports the development of antibacterial ceramic scaffolds derived from natural bovine bone. The bones were processed through sequential boiling and hydrogen peroxide treatment to remove organic matter, producing porous, mineral‐rich scaffolds.
Mohamad Hassan Taherian +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A distinct semi‐confined inner‐tube chemical vapor deposition geometry enables reproducible, large‐area growth of phase‐pure 2D β′‐In2Se3 from InI + Se precursors. Engineering local vapor transport and optimizing precursor delivery and temperature–time conditions yield uniform continuous films.
Dasun P. W. Guruge +8 more
wiley +1 more source
Residual Stress and Critical Crack Size before and after Post-Weld Heat-Treatment
, 2016 Post-weld heat-treatment (PWHT) is performed to reduce residual stress, but is not always possible to perform. The residual stresses on a thick section weld on a gas pipeline were determined before and after PWHT to assess residual stress and critical ...
Nicholas Hoye (20126040) +3 more
core
Effect of Fe Content and Post-Heat Treatment on Mechanical and Corrosion Properties of Ti-5Mo-xFe (x = 2, 4 wt%) Alloys Fabricated by Hydrogenation-Dehydrogenation Process. [PDF]
Materials (Basel)Park JY, Kang M, Park JH, Lee DG.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source