Results 171 to 180 of about 14,800,641 (243)
Some of the next articles are maybe not open access.
Synthesis of ZnO nanowires with supercritical carbon dioxide and post heat treatment
Nanotechnology, 2018Abstract Zinc oxide (ZnO) nanowires are used in applications such as gas sensors and solar cells. This work presents a novel synthesis route for ZnO nanowires using supercritical carbon dioxide (scCO 2 ) and post heat treatment. The method used scCO 2
Aaretti Kaleva +7 more
openaire +4 more sources
On Reducing the Post-Heat-Treatment Time of the Weldment
Journal of Materials Engineering and Performance, 2000Post heat treatment of weldments is one of the most extensively used techniques by the industrial community for relieving welding residual stresses. Such practice not only delays the manufacturing process, but also increases the cost of manufacturing. In this article, an idea of a new welding technique, which is a promising tool for relieving welding ...
S. Jahanian, R.R. Kunde, P.V. Kuppa
openaire +1 more source
, 2020
Post-fabrication heat treatment, including solution treatment (at 520 °C for 1 h) followed by water quenching (WQ), air cooling (AC) and furnace cooling (FC), was performed on a selective laser melted AlSi10Mg alloy. The objective is to assess the effect
F. Alghamdi +5 more
semanticscholar +1 more source
Post-fabrication heat treatment, including solution treatment (at 520 °C for 1 h) followed by water quenching (WQ), air cooling (AC) and furnace cooling (FC), was performed on a selective laser melted AlSi10Mg alloy. The objective is to assess the effect
F. Alghamdi +5 more
semanticscholar +1 more source
Post-heat treatment effect on the dielectric response of epoxy samples
2009 IEEE Conference on Electrical Insulation and Dielectric Phenomena, 2009In the present experiment, the dielectric response of various types of epoxies was investigated in the frequency and time domain. The samples consisted of nanostructured epoxy microcomposites and reference microcomposites. Water ingression at the fabrication step and/or at measuring time is known to affect the dielectric response of materials such as ...
M.F. Frechette +3 more
openaire +1 more source
Effect of post-heat treatment on microstructure and properties of EH47 steel CGHAZ
Materials Science and Technology, 2023To clarify the effect of post-heat treatment on the microstructure and mechanical properties of the coarse-grained heat-affected zone (CGHAZ) for EH47 steel, simulated CGHAZ specimens were subjected to post-heat treatment at 250°C for 1.0 h. The results showed that the microstructure of CGHAZ was composed of granular bainite (GB) and lath bainite (LB),
Xiaocong Yang +4 more
openaire +1 more source
, 2020
This paper aims to investigate the influence of different post-annealing cooling conditions, i.e. furnace cooling (heat treatment (HT) 1 – slow cooling) and air cooling (HT 2 – fast cooling), on the microstructure and mechanical properties of selective ...
S. Waqar +4 more
semanticscholar +1 more source
This paper aims to investigate the influence of different post-annealing cooling conditions, i.e. furnace cooling (heat treatment (HT) 1 – slow cooling) and air cooling (HT 2 – fast cooling), on the microstructure and mechanical properties of selective ...
S. Waqar +4 more
semanticscholar +1 more source
Mechanical Properties of the TiAlSiN Coatings by Post Heat Treatments
2009In this study, TiAISiN coatings were deposited by cathodic arc evaporation from titanium, aluminum and silicon alloy targets in a reactive nitrogen atmosphere at substrate bias of −50 V. The as-deposited coatings were then subjected to post heat treatment at 400 °C in nitrogen ahnosphere.
Wei-Yu Ho +5 more
openaire +1 more source
Key Engineering Materials, 2014
During the last few years various experimental destructive and non-destructive methods were developed to evaluate residual stresses. However it is impossible to obtain a full residual stress distribution in welded structures by means of experimental methods.
Sepe, Raffele +4 more
openaire +4 more sources
During the last few years various experimental destructive and non-destructive methods were developed to evaluate residual stresses. However it is impossible to obtain a full residual stress distribution in welded structures by means of experimental methods.
Sepe, Raffele +4 more
openaire +4 more sources
Materials letters (General ed.), 2020
Thin-walled A357 aluminum alloy components were built through wire-arc additive manufacturing. The microstructure and mechanical properties of the as-deposited and heat-treated components were investigated.
Xue-Wei Fang +5 more
semanticscholar +1 more source
Thin-walled A357 aluminum alloy components were built through wire-arc additive manufacturing. The microstructure and mechanical properties of the as-deposited and heat-treated components were investigated.
Xue-Wei Fang +5 more
semanticscholar +1 more source
Progress in Photovoltaics, 2020
Cu2ZnSn(S,Se)4 (CZTSSe) thin‐film solar cells offer various advantages including excellent optical and electrical properties, nontoxic and earth‐abundant raw materials, and a simple fabrication process.
Sungu Hwang +8 more
semanticscholar +1 more source
Cu2ZnSn(S,Se)4 (CZTSSe) thin‐film solar cells offer various advantages including excellent optical and electrical properties, nontoxic and earth‐abundant raw materials, and a simple fabrication process.
Sungu Hwang +8 more
semanticscholar +1 more source

