Results 41 to 50 of about 34,463 (271)
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Metals, 2022 In this study, 2024 aluminum alloy was diffusion bonded to identify the effect of the bonding temperature, applied pressure, and heating time on the microstructure, hardness, and bonding strength.
Meng-Ting Chiang +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source
Metals, 2019 This paper investigated the microstructure and mechanical properties of a friction-stir-welded beryllium-copper alloy, which is difficult to weld with conventional fusion welding processes.
Yeongseok Lim +2 more
doaj +1 more source
Journal of Materials Research and Technology, 2020 Effect of post-weld heat treatment on the intergranular corrosion of ENiCrFe-7 weld overlay cladding materials was investigated. The results showed that Cr-rich precipitates occured in the dendrites and grain boundaries, and Cr-depletion areas appeared ...
P.L. Guo, L.G. Ling
doaj +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Pre-weld heat treatment improves welds in Rene 41 [PDF]
, 1968 Cooling of Rene 41 prior to welding reduces the incidence of cracking during post-weld heat treatment. The microstructure formed during the slow cooling rate favors elevated temperature ductility.
Prager, M.
core +1 more source
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Journal of Manufacturing and Materials ProcessingTo achieve the desired material properties of automotive components made by friction welding, post-weld heat treatment is critical. The high temperatures encountered during the friction welding of steels can lead to changes in the microstructure ...
Rajesh Jesudoss Hynes Navasingh +5 more
doaj +1 more source