Results 231 to 240 of about 15,148,331 (301)
Some of the next articles are maybe not open access.
, 2021
Joining of two materials having different physical, chemical, and thermal properties and to make the joint tough and stiff, special attention and investigation are required.
Mahmud Khan +2 more
semanticscholar +1 more source
Joining of two materials having different physical, chemical, and thermal properties and to make the joint tough and stiff, special attention and investigation are required.
Mahmud Khan +2 more
semanticscholar +1 more source
Hyperbaric Post Weld Heat Treatment
Offshore Technology Conference, 1983ABSTRACT This paper describes a sub-sea hyperbaric Post Weld Heat Treatment (PWHT) system developed jointly by SHELL UK EXPLORATION & PRODUCTION and COMEX DIVING. It discusses:Assessment of power requirements and equipment,Initial tests conducted in the COMEX hydrosphere and in shallow water in Marseille,Full ...
Stuart Saunderson, David Waller
openaire +1 more source
In-Situ Post-Weld Heat Treatment of Wet Welds
Offshore Technology Conference, 19921.0 Introduction There is a substantial interest in implementing wet welding for structural repairs of offshore installations. Some of the restrictions to its use are heat affected zone (HAZ) hardening and cracking, and the inability to produce wet welds that meet the bend test requirements of a surface weld ...
Peter Szelagowski +3 more
openaire +1 more source
Welding, Repair and Local Post Weld Heat Treatment Residual Stresses
Volume 2: Computer Technology & Bolted Joints; Design & Analysis, 2023Abstract The study presented deals with an industrial case and relates to the calculation of the residual stresses in a butt weld of two shells of large diameter, high thickness and great length constituting part of pressure equipment. After completion of the weld, it can be repaired if unacceptable defects are detected ...
François Billon +4 more
openaire +1 more source
, 2021
The dissimilar austenitic stainless steel (AISI316) and low carbon steel (AISI1018) have been welded without filler metal by CO2 4 kW laser welding. Then, the effect of Post Weld Heat-Treatment (PWHT) on the microstructure, tensile and yield strength ...
M. Prabakaran, G. Kannan
semanticscholar +1 more source
The dissimilar austenitic stainless steel (AISI316) and low carbon steel (AISI1018) have been welded without filler metal by CO2 4 kW laser welding. Then, the effect of Post Weld Heat-Treatment (PWHT) on the microstructure, tensile and yield strength ...
M. Prabakaran, G. Kannan
semanticscholar +1 more source
Materials Science and Technology
The corrosion behaviour and the influence of nickel and post-weld heat treatment (PWHT) on the susceptibility to corrosion in welded duplex stainless steels were investigated. After PWHT, the amount of nickel for the weld region increases resulting in the
Ali Tahaei +4 more
semanticscholar +1 more source
The corrosion behaviour and the influence of nickel and post-weld heat treatment (PWHT) on the susceptibility to corrosion in welded duplex stainless steels were investigated. After PWHT, the amount of nickel for the weld region increases resulting in the
Ali Tahaei +4 more
semanticscholar +1 more source
Post-weld heat-treatment cracking in superalloys
International Metals Reviews, 1983This review is concerned with a type of cracking that often occurs during the postweld heat-treatment of Ni-base superalloys. The metallurgical factors and process variables that influence crack sensitivity are discussed in detail. The various types of tests available to study this type of embrittlement and the limitations of each approach are briefly ...
R. Thamburaj, w. Wallace, J. A. Goldak
openaire +1 more source
, 2021
In the present study, the Gas Tungsten Arc Weld (GTAW) joint of P91 steel was produced using the dissimilar IN617 grade filler wire. The welded joints have been subjected to different post-weld heat treatment (PWHT) to obtain the stable microstructure ...
Sanjeev Kumar, C. Pandey, A. Goyal
semanticscholar +1 more source
In the present study, the Gas Tungsten Arc Weld (GTAW) joint of P91 steel was produced using the dissimilar IN617 grade filler wire. The welded joints have been subjected to different post-weld heat treatment (PWHT) to obtain the stable microstructure ...
Sanjeev Kumar, C. Pandey, A. Goyal
semanticscholar +1 more source
IN792 DS Superalloy: Optimization of EB Welding and Post-Welding Heat Treatments
Materials Science Forum, 2016Electron beam (EB) welding has been used to realize the seams on 2 mm thick plates of directionally solidified (DS) IN792 superalloy. A grid of the samples has been prepared by varying the pass speed v from 1 to 2.5 m/min, while the other process parameters (power P = 1 kW, acceleration voltage T = 50 kV, beam current I = 20 mA) were kept constant ...
Barbieri G. +4 more
openaire +4 more sources
Journal of Manufacturing Processes, 2021
This study investigated the effects of post-weld heat treatment (PWHT) on microstructures and properties of a laser welded joint of high-strength and high-toughness titanium alloy, namely Ti-5Al-5V-5Mo-3Cr-1Zr (Ti-55531).
Jian Long +6 more
semanticscholar +1 more source
This study investigated the effects of post-weld heat treatment (PWHT) on microstructures and properties of a laser welded joint of high-strength and high-toughness titanium alloy, namely Ti-5Al-5V-5Mo-3Cr-1Zr (Ti-55531).
Jian Long +6 more
semanticscholar +1 more source

