Results 241 to 250 of about 15,148,331 (301)
Some of the next articles are maybe not open access.

Effects of a post-weld heat treatment on the microstructure and mechanical properties of dual-spot laser welded-brazed Ti/Al butt joints

, 2021
The influence of a post-weld heat treatment (PWHT), which included a solution treatment and an artificial aging treatment, on the microstructure and mechanical properties of laser welded-brazed Ti/Al joints with Al-12Si filler was investigated.
Peng Li   +3 more
semanticscholar   +1 more source

Dissimilar Welding of Nickel Based Superalloy with Stainless Steel: Influence of Post Weld Heat Treatment

Materials and Manufacturing Processes, 2021
Dissimilar welding potentially has great importance for many industries. Joining of two different alloys is very challenging. In this paper, an attempt was made to produce a reliable joint between Nickel-based superalloy with stainless steel using the ...
D. Gope, S. Chattopadhyaya
semanticscholar   +1 more source

A viscoplastic model for numerical simulation of welding and post-weld heat treatment

Le Journal de Physique IV, 1999
A viscoplastic model is developed to perform numerical simulation of welding and post-weld heat treatment in an industrial context. It can describe with the same formalism the steel inelastic behaviour all along the process: time-independent plastic at low temperature, viscoplastic at higher temperature and viscous fluid for melted metal.
A. Razakanaivo, F. Waeckel
openaire   +1 more source

Effect of filler wire and post weld heat treatment on the mechanical properties of laser beam-welded AA2198

, 2021
The mechanical behavior of autogenously and non-autogenously laser beam-welded joints of Al-Cu-Li alloy AA2198 and the effect of post weld heat treatment are examined in this contribution. The deformation texture of the base material does not present any
T. Examilioti   +4 more
semanticscholar   +1 more source

Improvement of Post Weld Heat Treatment Rules on Welded Joints

1989
In order to improve the post weld heat treatment rules on welded joints, a cooperative programme of research, sustained by the Minsistry of Research and Technology has been set up on 1985. The study concerning the behaviour to fracture of as welded and post weld heat treated joints in SE 701 steel with great sizes permitted to lay down the influence of
J. Gilgert   +5 more
openaire   +1 more source

Addressing the abnormal grain coarsening during post-weld heat treatment of TIG repair welded joint of sand-cast Mg-Y-RE-Zr alloy

, 2021
Tungsten inert gas (TIG) repair welding is one of the key methods to reduce the rejection rate of sand-cast Mg-Y-RE-Zr alloys containing casting defects, and welding heat treatment can further improve the joint efficiency of the repaired joints.
Xin Tong   +7 more
semanticscholar   +1 more source

Phase transformation and the mechanical characteristics of heat-affected zones in austenitic Fe–Mn–Al–Cr–C lightweight steel during post-weld heat treatment

Materials Characterization, 2021
We identified the influence of post-weld heat treatment (PWHT) on the heat-affected zone (HAZ) in the Fe–29.7Mn–10.5Al–3.06Cr–0.93C (wt%) lightweight alloy based on transitions in its microstructure and mechanical properties.
Seonghoon Jeong   +6 more
semanticscholar   +1 more source

Effect of post-weld heat treatment on mechanical properties and fatigue crack growth rate in welded AA-2024

Materials Science & Engineering: A, 2020
In this study, effect of post weld heat-treatment (PWHT) at two different aged temperatures was investigated on the microstructure and the material properties of the aluminum alloy 2024.
V. Yadav, V. Gaur, I. Singh
semanticscholar   +1 more source

Post Weld Heat Treatment of Friction Stir Welded AA2017

2012
In this study a friction stir welded AA2017 is post weld heat treated at 500 °C for holding time of 20, 40 and 60min then quenched in water and naturally aged. The effect of post weld heat treatment on the microstructure and hardness is investigated across the transverse cross section of the weld.
M. M. Z. Ahmed, B. P. Wynne
openaire   +1 more source

Low stress welding technology without post-weld heat treatment

Materials Science and Technology, 2009
In order to assure the tightness and the service life of a full welded body ball valve, the temperature of grommet cannot exceed 150°C. Therefore, post-weld heat treatment cannot be used to relieve the welding residual stresses. In this study, a low stress welding technology was studied.
J. J. Xu, L. G. Chen, C. Z. Ni
openaire   +1 more source

Home - About - Disclaimer - Privacy