Results 161 to 170 of about 900,171 (314)

Spray Drying of Aonla Juice Mixed With Giloy Extract for Process Optimization, Product Development and Characterization. [PDF]

Food Sci Nutr
Jhally G, Sharma SR, Kaur K, Alam MS, Rani S, Mittal TC, Chavan P, Jaiswal AK.   +7 more
europepmc   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

CHARACTERIZATION AND SIMULATION OF MACROSCALE MOLD-FILLING DEFECTS IN MICROMINIATURE POWDER INJECTION MOLDING

, 2019
While micromolding with polymers has met with success, material homogeneity remains a critical issue in powder injection molding (PIM) because separation of the powder and binder results in defects in metal or ceramic microparts.
German, RM, Laddha, SG, Atre, SV, Lee, S, Wu, C, Park, SJ, Ahn, S   +6 more
core  

Mix Design and Performance Analysis of Concrete with Limestone Powder Admixture. [PDF]

Materials (Basel)
Gong F, Xu M, Wu J, An P, Shi W.
europepmc   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

A Study on the Properties of Blended Recycled Micro Powder Concrete and Insulation Boards Produced via Microbial Foaming. [PDF]

Materials (Basel)
Zhang HY, Li GQ, Bai HB, Zhang YJ, Rong H, Li XG.   +5 more
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Mechanical and microstructural performance evaluation for cement-based mortar: calcined mud powder. [PDF]

Sci Rep
Kurt Z.
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Application of Mixed Shell Powder as Modifier and Filler in Asphalt Mixture. [PDF]

Materials (Basel)
Wang C, Yang Y, Gong F, Cheng X, Ma B.
europepmc   +1 more source