Results 61 to 70 of about 49,283 (291)
Development of low cost inkjet 3D printing for the automotive industry : a thesis presented in partial fulfilment of the requirements for a degree of Master of Engineering in Mechatronics, Massey University, Albany, New Zealand [PDF]
, 2017 The aim of this project is to develop a low cost, powder based 3D printer that utilises inkjet printing technology. The 3D printer uses a standard drop-on-demand inkjet print head to deposit a binder onto the powder bed one layer at a time to build the ...
Dixon, Blair
core
Impact of mechanical and microstructural properties of potato puree-food additive complexes on extrusion-based 3D printing [PDF]
, 2018 This paper studies the applicability of extrusion-based 3D printing for constructing novel shapes from potato puree and the effects of four additives (agar, alginate, lecithin, and glycerol) added separately at three concentrations (0.5, 1, 1.5%) on the ...
Dankar, Iman +4 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh +3 more
wiley +1 more source
Additive Manufacturing LettersThe uniformity of the powder bed in Binder Jet Printing can impact the final properties of additively manufactured components. Granular flow phenomena, such as particle size segregation can influence the uniformity of the powder bed. Due to the 3D nature
Julia G. Behnsen +4 more
doaj +1 more source
3DRSP: Matlab-based random sphere packing code in three dimensions
SoftwareX, 2022 A svert Matlabsvert -based computational procedure is proposed to fill a given volume with spheres whose radii are randomly picked from any specified probability distribution supported by svert Matlabsvert .
Travis J. Black, Alexei F. Cheviakov
doaj +1 more source
3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs
Advanced Engineering Materials, EarlyView.This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu +4 more
wiley +1 more source
Acta Polytechnica CTU Proceedings, 2019 The paper is focused on evaluation of the relation between mechanical properties of 3D printed stainless steel 316L-0407 and printing direction (i.e. the orientation of the part which is being printed in the manufacturing device) subjected to compressive
Michaela Neuhäuserová +5 more
doaj +1 more source
Binder jet green parts microstructure: advanced quantitative analysis
Journal of Materials Research and Technology, 2023 3D binder jet technology has drawn significant attention in recent years thanks to its ability to build complex shapes with a wide variety of commercial powders, together with the advantage of not using high energy sources during the printing process ...
Sergi Bafaluy Ojea +4 more
doaj +1 more source
Design and manufacturing of a Selective Laser Sintering test bench to test sintering materials [PDF]
, 2016 The goal of this project is to design and build a prototype of recoating system for a laser cutting machine to turn it into a selective laser sintering printing machine.
Gall Trabal, Guillem +1 more
core