Results 11 to 20 of about 1,327,582 (300)
Powder co-injection moulding [PDF]
, 2000 A novel powder processing technique has been developed by combining conventional powder injection moulding with polymer co-injection moulding, to permit the in-situ surface engineering of metal or ceramic components as an integral step within the ...
Hanson, S. M. J.
core +7 more sources
Investigation of Insert Materıal in Inserted Powder Injection Molding
Gazi Üniversitesi Fen Bilimleri Dergisi, 2020 Inserted powder injection molding (IPIM) is a method developed to produce of thick parts (> 10 mm). In this method, feedstock is injected onto the previously prepared inserts.
Mehmet SUBAŞI +2 more
doaj +1 more source
Analysis of biomedical titanium implant green parts by X-Ray tomography
Journal of Materials Research and Technology, 2021 In this study, X-ray tomography was applied as a non-destructive test to investigate the internal defects of the green part produced with Powder injection molding (PIM).
Levent Urtekin +2 more
doaj +1 more source
Development and design of binder systems for titanium metal injection molding: An overview [PDF]
, 2013 Titanium metal injection molding (Ti-MIM) has been practiced since the late 1980s. Logically, the Ti-MIM practice follows the similar processes developed for the antecedent materials such as stainless steel and ceramics.
Neil Edmonds +9 more
core +1 more source
Analysis of rheological behaviour of titanium feedstocks formulated with a water-soluble binder system for powder injection moulding [PDF]
, 2014 Binder selection and formulation are critical in powder injection moulding. Binders play a key role in controlling the rheological properties of a feedstock and influence whether the resulting feedstock can be successfully injection moulded, debound and ...
Pickering, Kim L. +3 more
core +1 more source
INJECTION MOLDING OF STRUCTURED MULTIPHASE MATERIALS
RUDN Journal of Engineering Research, 2017 Contemporary and future-oriented mechanical engineering requires the use of a new set of methods for processing, manufacturing, changing the state of materials implemented in the production process.
A B Semenov +3 more
doaj +1 more source
Simulation on the Two-phase Separation of Powder Injection Molding 316L Stainless Steel
Medžiagotyra, 2019 By utilizing the FLUENT software, finite element simulation analysis was performed on the two-phase separation of powder injection molding, and the simulation results were verified through experiment.
Feng SHANG +5 more
doaj +1 more source
Gas Atomization Parametric Study on the VIGA-CC Based Synthesis of Titanium Powder [PDF]
Archives of Metallurgy and Materials, 2020 With the recent advancement in technology for titanium metal powder injection molding and additive manufacturing, high yield and good flowability powder production is needed.
Dae-Kyeom Kim +6 more
doaj +1 more source
Hittite Journal of Science and Engineering, 2017 I n this study, influence of hydrolic pressure or gas pressure on the powder injection molding of 316L stainless steel was investigated. Variations in the microstructure, hardness and density of the porduced samples were discussed in the frame of presure
Yunus Turen
doaj +1 more source
Injection Molding of β-TCP Powder
Journal of the Ceramic Society of Japan, 1992 Injection molding of β-TCP powder was studied. Rod like test pieces (φ6×50l) were produced by the injection molding using three powder-binder compound: (I) β-TCP and several organic binders; (II) β-TCP, alumina (3-9wt%) and several organic binders; (III) β-TCP, zirconia (3-9wt%) and several organic binders. After the binder extraction process, the test
KANKAWA, Yoshimitsu +2 more
openaire +2 more sources