Results 291 to 300 of about 78,164 (342)

Fabrication of micro-sized piezoelectric structure using powder injection molding with separated mold system

Ceramics International, 2018
In this research, a powder injection molding process was developed to fabricate a micro-sized piezoelectric structure with high aspect-ratio. The separated mold system was prepared by the X-ray micromachining process.
J. M. Park, J. Han, C. Gal, Joo Won Oh, J. H. Kim, K. Kate, S. Atre, Youngmoo Kim, S. Park   +8 more
semanticscholar   +1 more source

Synergy of low-and high-density polyethylene in a binder system for powder injection molding of SiC ceramics

Ceramics International, 2022
H. Li, Yi peng Zhao, Guo-qing Chen, Ming Li, Xuesong Fu, Wenlong Zhou   +5 more
semanticscholar   +1 more source

Applications for Metal Powder Injection Molding

2015
Abstract Metal injection molding (MIM) is a metalworking technology that has its origins as a commercial technology only dating back to the early 1970s. This article explores why the MIM is the preferred solution for many fabricated components.
Matt Bulger, Paul Hauck
openaire   +1 more source

Micro Powder Injection Molding (µPIM): Review

Applied Mechanics and Materials, 2011
Micro powder injection molding (µPIM) is the combination of micro injection molding and powder injection molding (PIM) technology. The increasing demands on market of microparts further intensify the development of this technology. µPIM process enables the use of a wide range of materials and broadens the applications of micro components.
Heng Shye Yunn, Norhamidi Muhamad, Abu Bakar Sulong   +2 more
openaire   +1 more source

Sinter bonding of AISI 4340 and WC-Co using Ni interlayer by inserted powder injection molding

, 2019
An inserted powder injection molding (IPIM) method has been developed to overcome the size limitation (
Harun Koçak, M. Subaşı, Ç. Karataş
semanticscholar   +1 more source

Powder Injection Molding of Ti6Al4V Alloy

Materials Science Forum, 2007
An improved wax-based binder was developed for powder injection molding of Ti6A14V alloy. The molding behavior, debinding kinetics and sintering process were studied. Components with relative density of 96.5% were produced with PIM process. The density of the components was increased up to 99% by HIP treatment.
Xuan Hui Qu, Shi Bo Guo, Chun Feng Tang, Ming Li Qin, Xin Bo He, Syed Humail Islam   +5 more
openaire   +1 more source

Microstructural and core loss behaviors of addictive Fe-17 at% P based on Fe-3.5 wt% Si alloys in powder injection molding

Journal of Alloys and Compounds, 2018
This study investigated Fe-17 at% P addition effects on the magnetic properties of Fe-3.5 wt% Si alloys to enhance the electrical resistivity and core loss in powder injection molding.
D. Shin, Joo Won Oh, H. Kim, S. Park
semanticscholar   +1 more source

Mold filling simulation and experimental investigation of metallic feedstock used in low-pressure powder injection molding

International Journal of Material Forming, 2021
M. Azzouni, V. Demers, L. Dufresne
semanticscholar   +1 more source

Characterization of nano / micro bimodal 316L SS powder obtained by electrical explosion of wire for feedstock application in powder injection molding

, 2021
M. Krinitcyn, N. Toropkov, A. Pervikov, E. Glazkova, M. Lerner   +4 more
semanticscholar   +1 more source

Metal Powder Injection Molding of Microcomponents

2015
AbstractThis article discusses the process details of metal powder injection molding of microcomponents and the powder particle characteristics of feedstock and property requirements of binders. It reviews important characteristics to be considered in the processing steps: venting, channel diameters, binder segregation, binder degradation, feedstock ...
openaire   +1 more source