Results 191 to 200 of about 88,493 (352)

Tensile properties of powder-metallurgical-processed tungsten alloys after neutron irradiation near recrystallization temperatures

, 2020
Takeshi Miyazawa, Lauren M. Garrison, Josina W. Geringer, John Echols, Makoto Fukuda, Yutai Katoh, Tatsuya Hinoki, Akira Hasegawa   +7 more
openalex   +2 more sources

Micro and Nanoencapsulation of Omega‐3 Fatty Acids: Functional Applications and Future Perspectives in Food Systems

Food Safety and Health, EarlyView.
Whey protein‐based microencapsulation for omega‐3 PUFA delivery in food systems. Objective: Enhance oxidative stability & bioavailability of omega‐3 PUFAs using whey protein as an encapsulating agent. Current methods: Spray drying & coacervation—effective but limited by heat sensitivity and encapsulation efficiency. Emerging technologies: Electrospray &
Jihan M. Kassem, Fadwa W. Abdulqahar, Ahmed A. Zaky, Mohamed Said Boulkrane, Aya Darwish, Amr Farouk, Beraat Ozçelik, Osama Magouz, Xueming Liu, Tamer M. El‐Messery   +9 more
wiley   +1 more source

Non-destructive defect detection in powder metallurgy automotive oil pump stators using acoustic signals and machine learning classification. [PDF]

PLoS One
Hadizadeh Isfahani MH, Moeenfard H, Rohani A.   +2 more
europepmc   +1 more source

Powder Metallurgy Processing of Ti-Nb Based Biomedical Alloys

, 2018
Eren Yılmaz, Azim Gökçe, Fehim Fındık, H. Özkan Gülsoy   +3 more
openalex   +1 more source

Characterization of Powder Metallurgy Processed Pure Magnesium Materials for Biomedical Applications [PDF]

, 2017
Matěj Březina, Jozef Minda, Pavel Doležal, Michaela Krystýnová, Stanislava Fintová, Josef Zapletal, Jaromír Wasserbauer, Petr Ptáček   +7 more
openalex   +1 more source

Powder metallurgy Rene 95 rotating turbine engine parts, volume 2 [PDF]

A Rene 95 alloy as-HIP high pressure turbine aft shaft in the CF6-50 engine and a HIP plus forged Rene 95 compressor disk in the CFM56 engine were tested. The CF6-50 engine test was conducted for 1000 C cycles and the CFM56 test for 2000 C cycles.
Redden, T. K., Wilbers, L. G.
core   +1 more source

Total X‐Ray Illumination for Absolute Quantification of Crystalline Phases and Amorphous Content in PVDF and P(VDF‐TrFE)

Macromolecular Materials and Engineering, EarlyView.
A rigorous method, Total Illumination by X‐rays (TIX), is presented to quantify crystalline and amorphous phases in organic materials. Mitigating challenges such as low microabsorption and high amorphous content, an improved, general framework is established, applicable to polymers, MOFs, biological materials, etc.
Shaashwat Saraff, Giulio Isacco Lampronti, Sohini Kar‐Narayan   +2 more
wiley   +1 more source

Optimisation of powder metallurgy technology of 17-4 PH material. [PDF]

Heliyon
Kareem MQ, Mikó T, Gergely G, Gácsi Z.
europepmc   +1 more source

Analysis of Wear Properties of Powder Metallurgy Steel in Abrasive Soil Mass. [PDF]

Materials (Basel), 2022
Lemecha M, Napiórkowski J, Ligier K, Tarasiuk W, Sztukowski K.   +4 more
europepmc   +1 more source

Nanoquasicrystalline Al–Fe–Cr–Nb alloys produced by powder metallurgy

, 2013
F. Audebert, M. Galano, Carlos Triveño Ríos, H. Kasama, Maurício Mhirdaui Peres, Cláudio Shyinti Kiminami, Walter José Botta Filho, Claudemiro Bolfarini   +7 more
openalex   +2 more sources