Results 301 to 310 of about 918,356 (360)
Experimental Analysis for the Performance Assessment and Characteristics of Enhanced Magnesium Composites Reinforced with Nano-Sized Silicon Carbide Developed Using Powder Metallurgy. [PDF]
ACS OmegaFaisal N +8 more
europepmc +1 more source
Investigation of Microscopic Nonmetallic Inclusions in Powder Metallurgical High‐Speed Steels
steel research international, EarlyView.Methods for inclusion analysis are evaluated for suitability. Various powder metallurgical steels in different processing states are characterized. SEM/EDS data are further analyzed using analytical and statistical approaches. A thermodynamic method for determining inclusion phase composition is tested.
Manuel Schickbichler +5 more
wiley +1 more source
Biocarbon Suitability Evaluation for Direct Injection in Blast Furnace Ironmaking
steel research international, EarlyView.This study examines densified biocarbon for direct injection in blast furnace ironmaking to reduce greenhouse gas (GHG). Enhanced burnout performance, along with favorable reactivity and carbon structure of the combustion residue, supports its suitability for blast furnace injection. Modeling results indicate that up to a 27% reduction in GHG emissions
Xianai Huang +3 more
wiley +1 more source
Outline of a Washing Treatment to Improve Electric Arc Furnace Slag Environmental Behavior
steel research international, EarlyView.This study evaluates a water‐washing treatment for electric arc furnace slag to reduce the leaching of hazardous elements (Cr, Ba, Mo, and V), enabling its reuse. The process effectively decreases leachate concentrations. Using the treated slag as a substitute aggregate in concrete reduces greenhouse gases emissions by 42.5% compared to landfilling ...
Luca Testini +4 more
wiley +1 more source
steel research international, EarlyView.Cold spray deposition of stainless steel (grade: SS304) is evaluated for marine applications, with emphasis on martensitic transformation during impact. Analytical modeling, simulations, and experiments reveal that helium‐assisted spraying of fine powders promotes cooling below the martensitic start temperature, enabling up to ≈40% austenite to ...
Cal Vin Wong +4 more
wiley +1 more source
Journal of Vinyl and Additive Technology, Volume 31, Issue 2, Page 339-355, March 2025.Effecft of co‐doping polyaniline with phosphoric acid and phytic acid on the heat release rate of polyethylene. Abstract Polyolefins, such as polyethylene (PE), are highly flammable and electrically insulative, limiting their applicability. The study explored the flame‐retardancy and electrical conductivity of PE/polyaniline (PE/PANI) nanocomposites ...
Akeem Adisa +4 more
wiley +1 more source
Design and 3D Printing of Ceramic Insulation for Surface Flashover Mitigation in Vacuum
High Voltage, EarlyView.ABSTRACT Poor electrical strength of the ceramic–vacuum interface restricts the development of various electrical/electronic devices. Limitations of solutions based on conventional ceramics fabrication procedures are becoming prominent with the further demand for compactness and performance improvement.
Chao Wang +9 more
wiley +1 more source
Archaeometry, EarlyView.Abstract Kohl was ubiquitous in ancient Egypt and the Middle East, and routinely included among the toiletries deposited in burials. For Egypt, kohl recipes are increasingly well‐studied and known to use a range of inorganic and organic ingredients. Although these are often lead‐based, manganese‐ and silicon‐rich compounds are also attested.
Silvia Amicone +7 more
wiley +1 more source
Medicine for the Material World
Archaeometry, EarlyView.ABSTRACT It is clear that many of the inorganic materials of antiquity have been used both as medicines for human ills and also as agents in technological processes. This paper speculates that there might have been a stronger link between these two functions in the past, based on the concept of “active agents”—materials that are efficacious at curing ...
A. M. Pollard
wiley +1 more source