Results 11 to 20 of about 146,865 (265)
Fabrication of Porous Sintered Body using Shape-Controled 316l Stainless Steel Powder by High-Energy Ball Milling [PDF]
Archives of Metallurgy and MaterialsIn this study, 316L stainless steel powder was used to produce a porous body that could be used in a specific environment. In contrast to the existing method of producing filters using only spherical powders, we attempted to produce filters using plate ...
Woo Cheol Kim, Jongmin Byun
doaj +1 more source
Effect of Particle Shape on the Mixing of Powders
Journal of Pharmacy and Pharmacology, 1990 AbstractMixtures were prepared containing 200 g of 600 μm lactose and 0.5 g of 3 μm calcium carbonate of different particle shapes using a Y cone mixer. Measurements were made of the time required to achieve the acceptable standard deviation of mixing σA and of the segregation that occurred on subsequently vibrating the mixtures.
L W, Wong, N, Pilpel
openaire +2 more sources
The effect of particle shape on powder properties
Journal of Pharmacy and Pharmacology, 1969 Abstract Sand in the size ranges 18–20 mesh, 30–36 mesh and 44–60 mesh has been separated by means of a vibratory shape-sorting table into fractions of different shape. The ratios of the surface area of the particles to their volumes-the shape coefficients-ranged from 8 to 15.
K, Ridgway, R, Rupp
openaire +2 more sources
Effect of powder shape on effective thermal conductivity of Cu–Ni porous coatings
Journal of Materials Research and Technology, 2018 Porous coat is a kind of increasing heat transfer coatings based on increasing surface area and bubble nucleation. Several properties of the porous coat, including effective thermal conductivity (ETC) and porosity are influential design factors in ...
Mona Moayeri, Ali Kaflou
doaj +1 more source
Metals, 2023 As an attractive high-entropy alloy, AlCrCoNiCu high-entropy alloy has excellent corrosion resistance, wear resistance, and anti-bacterial capabilities, and is considered to be a potential substitute material for marine and nuclear industry materials ...
Zhiqiang Ren +7 more
doaj +1 more source
POWDER PARTICLE SHAPE AND SIZE DIFFERENTIATION
International Journal Of Multidisciplinary Research And Studies, 2022 The separation of particles in keeping with shape is important for improving the standard of powder products. the form of a particle significantly affects its bulk properties. Various kinds of shape separators reported up to now are reviewed during this paper to supply useful information when choosing the foremost effective one, and also the separation
Wranj Kargu, Garren Batceor
openaire +1 more source
Processing of complex near-net-shaped tungsten parts by PIM
Nuclear Materials and Energy, 2018 Powder Injection molding (PIM) as near-net-shape technology allows the effective mass fabrication of complex tungsten parts. Depending on the size and shape of the parts, for simple geometries only 20 s needed to produce a part.
Steffen Antusch +5 more
doaj +1 more source
Investigation of Rheological Behavior of Low Pressure Injection Molded Stainless Steel Feedstocks
Advances in Materials Science and Engineering, 2016 The purpose of this research is to investigate the influence of different powder loadings of 316L stainless steel (SS) powders on rheological behavior of feedstocks required for low pressure powder injection molding (L-PIM) process.
Muhammad Aslam +6 more
doaj +1 more source
MetalsIn order to supply high-purity process gas in the semiconductor manufacturing process, a gas filter is used to remove particles that may be contained in the gas.
Min-Jeong Lee +4 more
doaj +1 more source
Preparation Method of Spherical and Monocrystalline Aluminum Powder
Metals, 2019 This paper presents a new production method for a spherical and monocrystalline aluminum powder. Aluminum powder of irregular particle shapes was mixed with silica nanoparticles and heated to a temperature above the melting point of aluminum.
Mateusz Skalon +5 more
doaj +1 more source