Results 61 to 70 of about 366,434 (291)
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Syntheses and Characterization of Cadmium (II) Oxide Nanostructure from two Nano-sized Cadmium (II) Coordination Polymers [PDF]
Journal of Sciences, Islamic Republic of Iran, 2018 Two nano-sized mixed-ligand Cd (II) coordination polymers; [Cd (4,4' -bpy) (C4H4O4)].1/4 H2O (1) and[Cd(bpy)1.5 (NO3)2].3H2O (2) (bpy=bipiridine) were synthesized by a sonochemical method and characterized by elemental analyses, thermal gravimetric ...
M. J. Soltanian fard, A. Firoozadeh
doaj +1 more source
Synchrotron radiation: science & applications [PDF]
, 2015 This general talk is devoted to briefly introduce the main uses and applications of synchrotron radiation. An initial introduction will be dedicated to describe a synchrotron as a Large Facility devoted to produce photons that will be used to carry out ...
García-Aranda, Miguel Ángel
core
Crystal growth of LiGd1-xLuxF4 solid solutions by zone melting technique
, 2012 Mixtures (1 - x) LiGdF4 + x LiLuF4 (0.50? \leq x \leq 0.75) were melted and submitted to one zone melting cycle under a reactive HF atmosphere, aiming the study of the crystal growth of LiGd1-xLuxF4 solid solutions. Phase identification and compositional
Baldochi, S. L. +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani +2 more
wiley +1 more source
The Fabrication of a Biomedical Scaffold from Human Placenta [PDF]
The Iranian Journal of Veterinary Science and TechnologyThe powder derived from human placenta (HP) was successfully used in regenerative medicine. The purpose of this study was to fabricate powder from the human placenta and evaluate it by histological analysis, scanning electron microscopy, and X-ray ...
Jassim Khalaf Albozachri +1 more
doaj +1 more source
Simple Synthesis of Copper Oxide Nanoparticles in the Presence of Extractive Rosmarinus Officinalis leaves [PDF]
Journal of Nanostructures, 2016 In this work, copper oxide nanoparticles have been synthesized via extractive Rosmarinus Officinalis leaves by simple and economic co-precipitation method at ambient conditions which it has used (CH3COO)2Cu+H2O individually as Cu sources.
M. R. Mohammad Shafiee +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
, 2011 The cubic Prussian Blue (PB) analog, Zn3 [Fe(CN)6]2, has been studied by X-ray powder diffraction and inelastic neutron scattering (INS). X-ray data collected at 300 and 84 K revealed negative thermal expansion (NTE) behaviour for this material.
+5 more
core +1 more source
Confronting a cardiovascular system model with heart rate and blood pressure data. [PDF]
, 2005 The organic solid state appears in a complex number of forms. The design, synthesis and application of solid state organic materials have a big impact upon society, e.g. pharmaceuticals.
Fowler, A. C. +2 more
core +2 more sources