Results 111 to 120 of about 418,652 (294)
EAI Endorsed Transactions on Energy WebINTRODUCTION: Synchronous condensers (SCs) are installed near renewable energy stations to suppress transient overvoltage and enhance transmission capacity, but they increase SC transient power-angle instability risk post-fault.
Cheng Lü +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Model Power Sistem Stabilizer Berbasis Standar IEEE untuk Stabilitas Transien Sistem Tenaga Listrik
Semesta Teknika, 2016 Power System Stabilizers (PSS) are added to excitation systems, in order to enhance the damping of electric power system during low frequency oscillations. For large scale power systems comprising of many interconnected machines, the PSS parameter tuning
Agus Jamal
doaj
Control considerations for high frequency, resonant, power processing equipment used in large systems [PDF]
Addressed is a class of resonant power processing equipment designed to be used in an integrated high frequency (20 KHz domain), utility power system for large, multi-user spacecraft and other aerospace vehicles.
Mildice, J. W. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Taiyuan Ligong Daxue xuebaoPurposes Transmission power limit exists in point of common coupling (PCC) of grid-connected wind power, when the transmission power exceeds the limit, it may lead to voltage instability and broadband oscillation problems, threatening the safety and ...
GUO Xiaolong +4 more
doaj +1 more source
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source