Results 51 to 60 of about 279,761 (310)
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Droplet Collection Efficiency Regularity of NACA0012 Airfoil Based on the Eulerian Method
Aerospace, 2023 Obtaining droplet collection efficiency (DCE) is vital for icing numerical simulations. A droplet impact model based on the Eulerian two-phase flow model was established in this work to analyze the influence of different incoming flow parameters on DCE ...
Jie Wu +5 more
doaj +1 more source
Effects of POD control on a DFIG wind turbine structural system [PDF]
, 2020 This paper investigates the effects power oscillation damping (POD) controller could have on a wind turbine structural system. Most of the published work in this area has been done using relatively simple aerodynamic and structural models of a wind ...
Baloch, Shurooque +6 more
core +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source
Optimization and Evaluation of Cooling Structure of Stage 1 Blade of Heavy-Duty Gas Turbine
发电技术ObjectivesThe localization of core components of heavy-duty gas turbines holds significant importance for technological innovation, industrial upgrading, and even national security.
YU Wenchang +13 more
doaj +1 more source
Predictive control of wind turbines by considering wind speed forecasting techniques [PDF]
, 2009 A wind turbine system is operated such that the points of wind rotor curve and electrical generator curve coincide. In order to obtain maximum power output of a wind turbine generator system, it is necessary to drive the wind turbine at an optimal rotor ...
Jovanovic, Milutin +3 more
core
Integrated Optimal Design of a Passive Wind Turbine System: An Experimental Validation [PDF]
, 2010 This work presents design and experimentation of a full passive wind turbine system without active electronic part(power and control). The efficiency of such device can be obtained only if the system design parameters are mutually adapted through an ...
Espanet, Christophe +3 more
core +4 more sources
Advanced Materials Technologies, EarlyView.Waterborne polyurethane/graphene formulations are developed as piezoresistive coatings on glass fabric to enable flexible strain sensing. The graphene‐enabled conductive network provides a stable electromechanical response under cyclic compression. The coating demonstrates reliable pressure‐dependent resistance changes, highlighting its potential for ...
Vishnu Vijayan Pillai +8 more
wiley +1 more source
Advances in Mechanical Engineering, 2023 A thermoelastohydrodynamic (TEHD) coupling model is developed to study the static performance of a heavy-duty tilting pad thrust bearing (TPTB) under the effect of axis misalignment.
Binbin Liu +5 more
doaj +1 more source
Contra-rotating marine current turbines : single point tethered floating system - stabilty and performance [PDF]
, 2009 The Energy Systems Research Unit within the Department of Mechanical Engineering at the University of Strathclyde has developed a novel contra-rotating tidal turbine (CoRMaT). A series of tank and sea tests have led to the development and deployment of a
Clarke, Joseph Andrew +4 more
core