Results 101 to 110 of about 231 (210)

Structural behavior of reinforced concrete pre-stressed tapered beams

open access: yesPeriodicals of Engineering and Natural Sciences (PEN)
This research is focused on studying the flexural behavior of reinforced concrete prestressed (post-tensioned) tapered beams. The present study investigates the impact of compressive strength, prestressed reinforcement, and tapering ratio on flexural behavior.
openaire   +1 more source

RESEARCH OF THE WORK OF PRE-STRESSED WOODEN BEAMS MADE OF GLUELAMMED WOOD

open access: yesUrban development and spatial planning
It was established that the increase in stiffness allows for an increase in the overlap spans, which in turn will make it possible to save materials. Therefore, options for reinforcement, as well as options for prestressing wooden bending elements, were developed.
Denys Mykhailovskyi, Petro Gomon
openaire   +1 more source

Beyond Passivation: Designing Structurally Tailored Artificial Interphases for High‐Energy Lithium‐Based Anodes

open access: yesAdvanced Materials Interfaces, EarlyView.
This review outlines critical engineering design rules for building artificial protective coatings on next‐generation lithium metal and silicon battery anodes. It highlights how balancing structural flexibility with strict electronic and ionic transport limits prevents early battery failure.
Surin Gupte, Vilas G. Pol
wiley   +1 more source

Design of Pre-Stressed Concrete T-Beams

open access: yesInternational Journal of Scientific Engineering and Research, 2014
Rajamoori Arun Kumar, B Vamsi Krishna
openaire   +1 more source

Programmable Variable‐Stiffness Multilayer Elastomer Composites With High‐Aspect‐Ratio Low‐Melting‐Point Alloy Inclusions

open access: yesAdvanced Materials Technologies, EarlyView.
High‐aspect‐ratio low‐melting‐point alloy inclusions are embedded within multilayer silicone laminates to create thermally programmable stiffness. Sequential activation of alloy‐rich layers produces four distinct mechanical states and reconfigures tendon‐driven actuator trajectories under the same load.
Palpolage Don Shehan Hiroshan Gunawardane   +4 more
wiley   +1 more source

Aerosol Jet Printing of Benzocyclobutene as a Thermally Stable, Low‐Loss Dielectric for Multilayer Microwave Electronics

open access: yesAdvanced Materials Technologies, EarlyView.
Multilayer aerosol jet printed components with a low‐loss, thermally stable dielectric are demonstrated using benzocyclobutene. Ink formulation and in‐line droplet evaporation control support high‐quality, versatile, and stable printing performance. A specialized measurement for low‐loss materials reveals promising microwave properties, which, combined
Md Ramjan Ali   +3 more
wiley   +1 more source

Programmable Crack Networks for Wide‐Range and Reversible Strain Sensing in Vertically Oriented van der Waals Molybdenum Disulfide Thin Films

open access: yesAdvanced Materials Technologies, EarlyView.
Vertically oriented van der Waals MoS2 thin films enable a mechanically programmable crack network for strain sensing. The initial mechanical programming protocol establishes a programmed crack configuration along weak interlayer and interdomain interfaces.
Yinli Wang, Hiroyuki Hirakata
wiley   +1 more source

Liquid Crystal Elastomer Actuator Matrix for Large Area Applications

open access: yesAdvanced Materials Technologies, EarlyView.
A scalable approach is used to manufacture a digitally‐controllable, 2D 5 × 5 actuator matrix. The elements of the matrix are produced by direct ink writing of a liquid crystal elastomer ‘artificial muscle’ on large‐area flexible thin‐film heaters. In optimizing the low‐power actuators, multiple heater designs and substrate materials are investigated ...
Giulia Spallanzani   +5 more
wiley   +1 more source

Microscale 3D‐Printed Digital Strain Switches for Embedded Mechanical Computation

open access: yesAdvanced Materials Technologies, EarlyView.
Microscale 3D‐printed strain switches on flexible films convert deformation into native digital signals at geometry defined thresholds. A closed form model predicts switching from 3000 to 15 000 microstrain and is validated across 110 devices. Reliable ohmic closure and strain activated AND, OR, and XOR logic point toward low‐power mechanical ...
Regan Kubicek   +3 more
wiley   +1 more source

4D–Printed Photothermally Actuated Soft Microgripper on an Optical Fiber Tip for Biomedical Applications

open access: yesAdvanced Materials Technologies, EarlyView.
In this study, we developed a light–driven soft microgripper by 3D–printing a photo–crosslinkable, temperature–responsive hydrogel with embedded silver particles onto an optical fiber tip. The microgripper actuates via photothermal effects at cell culture temperature and can gently grasp spheroids without minimal damage, offering a compact, actuator ...
Shogo Oishi   +7 more
wiley   +1 more source

Home - About - Disclaimer - Privacy