Results 241 to 250 of about 12,292,407 (304)

Research on damage size effect of cemented paste backfill under high sand-cement ratio conditions. [PDF]

Sci Rep
Jiang D, Li H, Sun G.
europepmc   +1 more source

Experimental and Numerical Modal Analysis of Composite Sandwich Structures Using Surfboards as Model Systems

Advanced Engineering Materials, EarlyView.
This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan, Luca Lomazzi, Mathis Mercier, Kara Stark, Marc in het Panhuis   +4 more
wiley   +1 more source

Research on the mechanical behavior of compression molding for simulated polymer-bonded explosives. [PDF]

Sci Rep
Wu X, Tao J, Wang B, Ren H, Wang Y.
europepmc   +1 more source

Grain Refinement During Severe Plastic Deformation and Similitude of Subgrain Formation: A Molecular Dynamics Study

Advanced Engineering Materials, EarlyView.
Molecular dynamics is used to investigate structure refinement during severe plastic deformation. The results show similitude with experimental data. Molecular dynamics simulations of severe plastic deformation of monocrystalline and polycrystalline samples by multiaxial compression of aluminum are carried out.
Roberto B. Figueiredo
wiley   +1 more source

A critical review of chemical heterogeneity-driven microstructure control in steels. [PDF]

Appl Microsc
Lee SH, Kim JH.
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

CO₂ Laser Resection of Giant Rhinophyma Under Local Anesthesia: A Case Report. [PDF]

Clin Cosmet Investig Dermatol
Zhao QK.
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Laser Surface Hardening of Carburized Steels: A Review of Process Parameters and Application in Gear Manufacturing. [PDF]

Materials (Basel)
Kluczyński J, Jasik K, Łuszczek J, Pokropek J.   +3 more
europepmc   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source