Forging property, processing map, and mesoscale microstructural evolution modeling of a Ti-17 alloy with a lamellar (α+β) starting microstructure [PDF]
Science and Technology of Advanced Materials, 2017 This work identifies microstructural conversion mechanisms during hot deformation (at temperatures ranging from 750 °C to 1050 °C and strain rates ranging from 10−3 s−1 to 1 s−1) of a Ti-5Al-2Sn-2Zr-4Mo-4Cr (Ti-17) alloy with a lamellar starting ...
Hiroaki Matsumoto +5 more
doaj +2 more sources
Matlab Software for Supervised Habitat Mapping of Freshwater Systems Using Image Processing
Remote Sensing, 2021 We present a software package for the supervised classification of images useful for cover-type mapping of freshwater habitat (e.g., water surface, gravel bars, vegetation).
Johnathan M. Bardsley +2 more
doaj +1 more source
Analysis of hot deformation behavior and processing map of extruded AZ40 alloy
Cailiao gongcheng, 2021 The Gleeble-3500 thermal simulation tester was used to perform hot deformation behavior on the extruded AZ40 Mg alloy to analyze the trend of the true stress-strain curve after compression and to obtain the influence of the flow stress on the deformation
ZHI Sheng-xing +6 more
doaj +1 more source
Hot Workability Investigation of an Fe-Al-Ta Alloy Using Deformation Processing Maps
Metals, 2023 Fe-Al-Ta alloys are expected to replace high-alloyed steels in steam turbine blades. However, the mechanical properties of the forged blades are still not optimal due to limited grain refinement during hot forging and the coarse-grained microstructure ...
Aliakbar Emdadi +2 more
doaj +1 more source
Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy
Metals, 2022 An isothermal compression experiment was conducted to study the rheological behavior of Al-4.57Zn-1.50Mg-1.92Cu high-strength aluminum alloy at strain rates ranging from 0.1 to 20 s−1 and temperatures in the range of 573 to 773 K.
Jun Cai +7 more
doaj +1 more source
Metals, 2020 The hot deformation behavior of an advanced nickel-based Haynes282 superalloy was systematically investigated employing isothermal compression tests in the sub-solvus and super-solvus temperature with various strain rates.
Zhihao Yao +5 more
doaj +1 more source
Metals, 2021 The plasticity of Mg–6Zn–5Ca–3Ce alloy fabricated by rapid solidification (RS) at room temperature is poor due to its hexagonal-close-packed (HCP) structure.
Chengli Bao +6 more
doaj +1 more source
Deformation and Fracture Characterization of an Mg-Sn-Ca Alloy Using 3D Processing Maps
Metals, 2023 The deformation and fracture characterization of an Mg−2Sn−1Ca alloy were studied through uniaxial isothermal compression tests. The flow stress curves, the efficiency of power dissipation, the instability parameter and the fracture behavior of an Mg−2Sn−
Chenchen Zhi +8 more
doaj +1 more source
Hot deformation behavior of micro-alloyed steel using processing maps developed with different constitutive equations [PDF]
Journal of Mining and Metallurgy. Section B: Metallurgy, 2022 The hot workability of microalloyed steel was studied in the deformation temperature range of 850–1200ºC and strain rate of 0.001-100s-1. The constitutive relation of flow stress with temperature, strain rate and strain was established to construct ...
Thakur S.K., Das A.K., Jha B.K.
doaj +1 more source
Microstructure, Hot Deformation Behavior, and Textural Evolution of Mg-3Sn-2Al-1Zn-0.6Nd Alloy
Metals, 2022 To prepare wrought magnesium alloys with excellent plastic deformation properties, Mg-3Sn-2Al-1Zn-0.6Nd alloys were prepared. A hot compression test of Mg-3Sn-2Al-1Zn-0.6Nd alloy was carried out on a thermo-mechanical simulator.
Yuhang Guo +4 more
doaj +1 more source