Results 101 to 110 of about 3,648,979 (312)

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Reduction of Oxide Inclusions During the High‐Frequency Welding of Steel via a Nonthermal Ar/H2 Plasma Jet

Advanced Engineering Materials, EarlyView.
High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin, Lienhard Wegewitz, René Gustus, Henning Wiche, Wolfgang Maus‐Friedrichs   +4 more
wiley   +1 more source

Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma

Advanced Engineering Materials, EarlyView.
The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie, David Kramer, Thomas Scheithauer, Hans Jürgen Maier, Thomas Hassel   +4 more
wiley   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann, Berend Denkena, Hilke Petersen, Florian Schaper   +3 more
wiley   +1 more source

Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere

Advanced Engineering Materials, EarlyView.
A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz, Maik Szafarska, René Gustus, Kai Möhwald, Hans Jürgen Maier   +4 more
wiley   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland, Finn‐Lennard Janthur, Sarah Seffer, Jörg Hermsdorf, Ludger Overmeyer, Annika Raatz   +5 more
wiley   +1 more source