Results 31 to 40 of about 18,437 (250)
Circular utilization of discarded oyster farming bamboo scaffolding in pulp and papermaking
Scientific Reports, 2023 Oyster Farming is one of important fisheries and aquaculture industries in Taiwan. Each year, approximately 4000–5000 tons of discarded bamboo scaffolding (BS) used in oyster farming, are generated, so the treatment and utilization of BS should be taken ...
Hao-Chen Sun +5 more
doaj +1 more source
Advanced Functional Materials, EarlyView.Schematic illustration of LNP‐MPG nuclei‐targeting delivery of HMW‐FGF2 promoting histone acetylation to regulate the fate of DPSCs and treat spinal cord injury. LNPs components include pHMW‐FGF2 plasmid, DSPC, Dlin‐MC3‐DMA, cholesterol, and PEG2000, and are modified with MPG to form HMW‐FGF2@LNP‐MPG (HLM). HLM nuclei‐targets DPSCs to deliver HMW‐FGF2,
Heng Zhou +6 more
wiley +1 more source
Investigating the possibility of chemi-mechanical pulping of bagasse [PDF]
BioResources, 2013 Chemi-mechanical pulping was evaluated as a potential way to prepare sugarcane bagasse fibers for papermaking. Cellulose, lignin, ash, and extractives soluble in alcohol-acetone were measured as 55.75%, 20.5%, 1.85%, and 3.25%, respectively. Fiber length,
Alireza Khakifirooz +3 more
doaj
Recyclable Lignin‐Based Thermadapt Shape Memory Polymers With Near‐Infrared Light Response
Advanced Functional Materials, EarlyView.ABSTRACT Covalent adaptable networks (CANs) have been designed to address the recycling challenges associated with thermosets, while preserving their mechanical properties. However, producing biobased CANs with intelligent response capabilities remains challenging.
Jian Liu +8 more
wiley +1 more source
Anatomical and Chemical Characteristics of Bambusa multiplex for Pulping
Journal of Natural FibersBambusa multiplex is a small-diameter bamboo with potential as a non-wood pulping raw material, but its pulping-related characteristics remain insufficiently evaluated. In this study, B.
Peng Zhao +10 more
doaj +1 more source
Removal of wood extractives as pulp (pre-)treatment: a technological review
SN Applied Sciences, 2021 Wood extractives usually do not exceed five percent of dry wood mass but can be a serious issue for pulping as well as for the pulp itself. They cause contamination and damages to process equipment and negatively influence pulp quality.
Maximilian Lehr +2 more
doaj +1 more source
Leaftronics: Bio‐Fractal Scaffolds From Leaf Venation for Low‐Waste Electronics
Advanced Materials, EarlyView.“Leaftronics” transforms naturally evolved leaf venation into quasi‐fractal scaffolds for sustainable electronics. Polymer‐infiltrated leaf skeletons can be used to fabricate ultra‐smooth, reflow‐ and thin‐film‐compatible decomposable substrates, while making the same lignocellulose networks conducting results in flexible transparent electrodes.
Rakesh Rajendran Nair +3 more
wiley +1 more source
AgricultureSeed melon pulping is a critical process in the full utilization of seed melon. However, controlling the performance during the pulping process presents several challenges, particularly the unclear relationship between pulping performance and process ...
Qi Luo +7 more
doaj +1 more source
PARAMETER CALIBRATION OF RICE STRAW PARTICLE–CRUSHING MODEL [PDF]
Engenharia AgrícolaDiscrete element method is widely used to study grain particles; however, there is a lack of research on the mathematical model parameters of rice straw particles in the crushing simulation process.
Shuying Jiang +4 more
doaj +1 more source
Strong Fully Reprocessable Engineered Wood Composites
Advanced Materials, EarlyView.Engineering a hyperbranched adhesive with complementary imine‐bond and hydrogen‐bond networks, combining it with wood particles to fabricate the wood composite (WP/HTP) under mild hot‐pressing conditions. The WP/HTP exhibits 100% mechanical strength recovery after three cycles of reprocessing, and the reprocessed modulus of rupture (MOR) and modulus of
Xilin Zhang +9 more
wiley +1 more source