Results 61 to 70 of about 7,956,239 (250)

Chemical State Detection and Charge Transfer in Complex Oxide Heterostructures via In Situ Auger Electron Spectroscopy

open access: yesAdvanced Functional Materials, EarlyView.
In situ Auger Electron Spectroscopy resolves oxidation states with high fidelity during the pulsed laser deposition of multivalent perovskite manganate and vanadate heterostructures. The chemical‐state signature is carried by the valence‐electron population of the transition‐metal cation, read out through the relative intensities of Auger fine ...
Harish Kumarasubramanian   +1 more
wiley   +1 more source

THE INFLUENCE OF THE GAS NOOZLE GEOMETRICAL SHAPE ON THE QUALITY OF THE MAG WELDING DEPOSIT [PDF]

open access: yesFiabilitate şi Durabilitate, 2018
The paper aims to identify the effects on the geometrical configuration of the welding deposit caused by changes in the classical gas nozzle shape. The results obtained in the case of two geometrical shapes of the nozzles are presented after using ...
Dumitru Titi Cicic   +2 more
doaj  

Electrical properties, structural properties, and deep trap spectra of thin α-Ga2O3 films grown by halide vapor phase epitaxy on basal plane sapphire substrates

open access: yesAPL Materials, 2018
Undoped epitaxial films of α-Ga2O3 were grown on basal plane sapphire substrates by halide vapor phase epitaxy (HVPE) in three different modes: standard HVPE, HVPE with constant flow of Ga and pulsed supply of O2 (O2-control growth regime), and with ...
Dae-Woo Jeon   +9 more
doaj   +1 more source

Omnipolar Magnetic Field Detection by Superlattice‐Based Hall Sensor

open access: yesAdvanced Functional Materials, EarlyView.
Magnetic‐field‐induced electronic switching is demonstrated in unit‐cell‐engineered La0.7Sr0.3MnO3–BiFeO3 superlattices. Distinct substrate terminations modify magnetic and transport properties. Hall resistance measurements show omnipolar, hysteretic anomalous Hall switching above the Curie temperature, arising from Fe─Mn interfacial exchange, enabling
Mark Huijben   +6 more
wiley   +1 more source

Characterisation of surface and sub-surface discontinuities in metals using pulsed eddy current sensors [PDF]

open access: yes
Due primarily to today's rigorous safety standards the focus of non-destructive testing (NDT) has shifted from flaw detection to quantitative NIDT, where characterisation of flaws is the objective.
Sophian, Ali
core   +4 more sources

The effect of powder recycling in direct metal laser deposition on powder and manufactured part characteristics [PDF]

open access: yes, 2006
A potential way of improving the material efficiency and cost effectiveness of the Direct Metal Laser Deposition (DMLD) process is to take powder that is not utilised in each deposition attempt and re-use it in subsequent attempts (powder recycling ...
Ng, G   +17 more
core   +4 more sources

Device for controlling pulsed electrolysis mode in contact pad fabrication

open access: yesТехнологія та конструювання в електронній апаратурі, 2003
An electronic device for controlling electrolysis under pulsed voltage supply to an electrolytic cell has been developed. By varying the amplitude of voltage and current pulses, their duration, and duty cycle, it enables regulation of both the deposition
L. A. Albota   +3 more
doaj  

Spatially Modulated Morphotropic Phase Boundaries in a Compressively Strained Multiferroic Thin Film

open access: yesAdvanced Functional Materials, EarlyView.
ABSTRACT The coexisting rhombohedral‐like (R′, MA) and tetragonal‐like (T′, MC) monoclinic phases in compressively strained bismuth ferrite thin films exhibit exceptional piezoelectric and magnetic properties. While previous studies have largely focused on probing the morphotropic phase boundaries (MPBs) comprising ordered R′/T′ twins, their self ...
Ting‐Ran Liu   +7 more
wiley   +1 more source

Effect of ultrasonic frequency pulsed current on microstructure and mechanical properties of high-nitrogen steel additive manufacturing components

open access: yesHanjie xuebao
To improve issues such as mechanical property degradation and nitrogen escape during arc additive manufacturing of high-nitrogen steel (HNS), additive manufacturing experiments of HNS were conducted under ultrasonic frequency pulsed gas metal arc (UFP ...
Li MA   +5 more
doaj   +1 more source

Enhancement of positive pulsed corona by dielectric enclosure

open access: yesAIP Advances, 2019
In this work, the effect of positive pulsed corona enhancement by introducing Teflon dielectric enclosure in vicinity to the electrode assembly was studied.
Xingxing Wang   +2 more
doaj   +1 more source

Home - About - Disclaimer - Privacy