Results 91 to 100 of about 203,842 (307)
Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam
Advanced Engineering Materials, EarlyView.Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley +1 more source
Physical properties of V$_{1-x}$Ti$_{x}$O$_{2}$ (0 $<$ x $<$ 0.187) single crystals
, 2015 Free standing, low strain, single crystals of pure and titanium doped VO$_{2}$ were grown out of an excess of V$_{2}$O$_{5}$ using high temperature solution growth techniques.
Bud’ko, Sergey +4 more
core +3 more sources
Advanced Engineering Materials, EarlyView.Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies +2 more
wiley +1 more source
MetalsAlthough metallic materials have been used as load-bearing materials in dental and biomedical fields since they have good mechanical properties such as good ductility and strength, their aesthetic properties are inferior to those of ceramic or resin.
Yoshimi Watanabe +5 more
doaj +1 more source
Stress corrosion cracking of titanium alloys [PDF]
The effect of hydrogen on the properties of metals, including titanium and its alloys, was investigated. The basic theories of stress corrosion of titanium alloys are reviewed along with the literature concerned with the effect of absorbed hydrogen on ...
Beck, F. H. +3 more
core +1 more source
, 2007 This paper describes work which emerged through a need to understand more about the potential of laser surface engineering for use in the creative industries.
O'Hana, Sarah +2 more
core
Biomimetic implant surface functionalization with liquid L-PRF products: in vitro study [PDF]
, 2018 Objective: Platelet-rich fibrin (PRF) clots and membranes are autologous blood concentrates widely used in oral surgical procedures; less is known, however, about the liquid formulations of such products.
BOZZUTO, GIUSEPPINA +5 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study investigates the effects of milling parameters, including rotational speed, milling duration, and ball‐to‐powder ratio, on TiAl particle size and morphology in an XHV‐equivalent atmosphere. The creation of oxide‐free surfaces enhances the mechanical properties of green bodies.
Jytte Möckelmann +4 more
wiley +1 more source
Microstructure Evolution Through Cryogenic Rolling of Ultra-High Purity Titanium Produced by Electron Beam Melting [PDF]
Archives of Metallurgy and MaterialsIn this study, crystal grain refinement of pure titanium manufactured by electron beam melting through cryogenic rolling was performed. The effect of rolling in a cryogenic atmosphere on average grain size was investigated.
Ui Jun Ko +4 more
doaj +1 more source
Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites
Advanced Engineering Materials, EarlyView.Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter +9 more
wiley +1 more source