Results 61 to 70 of about 219,973 (335)
Real-time monitoring of proton exchange membrane fuel cell stack failure [PDF]
, 2016 Uneven pressure drops in a 75-cell 9.5-kWe proton exchange membrane fuel cell stack with a U-shaped flow configuration have been shown to cause localised flooding.
Brandon, NP +5 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
EnergiesEnhancing energy efficiency is essential for proton exchange membrane fuel cells (PEMFCs) operating in a dead-ended anode (DEA) mode. This study proposes the integration of a buffer tank, positioned between the mass flow meter and the fuel cell, to ...
Trung-Huong Tran +3 more
doaj +1 more source
The Purge of Civil Servants in Soviet Occupied Lithuania between June–December 1940
Genocidas ir Rezistencija, 2000 Soviet occupation succeeded by annexation and the accession of the Lithuanian communists to power, the task of whom was to form a puppet Government and carry out the plans of the country's sovietisation, brought about the purge of civil servants.
Nijolė Maslauskienė
doaj +1 more source
Measurement of neutron spectra in liquid hydrogen final report [PDF]
, 1964 Neutron spectrum measurement in liquid hydrogen and ...
Audas, J. H. +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
Effect of purge air on rotor endwall heat transfer of an axial turbine
Journal of the Global Power and Propulsion Society, 2017 In order to gain in cycle efficiency, turbine inlet temperatures tend to rise, posing the challenge for designers to cool components more effectively. Purge flow injection through the rim seal is regularly used in gas turbines to limit the ingestion of ...
Sebastiano Lazzi Gazzini +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
An economical vent cover [PDF]
, 1972 Inexpensive formed-plastic vent cover has been developed that allows controlled purge of vent systems and also provides blowout protection. Cover can also be used in relief mode to allow normal system relief flows without disengaging from vent system ...
Lee, A. C., Mcdonald, M. D.
core +1 more source
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source