Results 101 to 110 of about 16,271,237 (294)
Concrete modeling in finite element push-out test simulations [PDF]
, 2023 Push-out tests are commonly used to investigate the shear performance of mechanical connectors applicable in steel-concrete composite beams. These tests can be complemented by numerical finite element simulations to reduce the need for extensive ...
Spremić, Milan +2 more
core
Magneto‐Ionic Devices With Polymer‐Based Electrolytes
Advanced Functional Materials, EarlyView.Polymer electrolytes are introduced for magneto‐ionic devices based on hydroxide and hydrogen ions. The magneto‐ionic effect results in a pronounced voltage‐controlled variation of coercivity in both devices. The switching speed is in the range of 100 ms.
Markus Gößler +3 more
wiley +1 more source
Advanced Functional Materials, EarlyView.For the first time, an extreme‐thick laser‐arc PVD ta‐C (DLC) coating exceeding 100 µm is demonstrated, opening up new possibilities for ultra‐high load bearing capacity. This superhard amorphous carbon architecture combines >50% sp3 bonding, robust adhesion and self‐supporting performance, shielding substrates from plastic flow under extreme contact ...
Martin Zawischa +3 more
wiley +1 more source
A Miniaturized Autonomous Thermomagnetic Generator
Advanced Functional Materials, EarlyView.Micro, autonomous and high power thermomagnetic generator operating between a heat dissipator and a processor. ABSTRACT Thermomagnetic generators (TMG) are promising devices for converting low‐grade waste heat into electricity. Self‐actuation using permanent magnets is the key to autonomy.
Morgan Almanza +11 more
wiley +1 more source
Formulating a design for a screw-type shear connector in a compo-site section
Ingeniería e Investigación, 2011 Screws-type shear connectors have been most used in Colombia during the last decade; however, an expression for their design in composite sections has only recently been presented (NSR10, paragraph F.2.9.8.2.2).
Maritzabel Molina Herrera +1 more
doaj
Considerations about the use of the “push‐out” test in Endodontic research [PDF]
International Endodontic Journal, 2015 Moinzadeh, A.T. +2 more
openaire +5 more sources
Switching Superconductivity with Uniaxial Strain in a high‐Tc${\rm T}_{c}$ Cuprate Superconductor
Advanced Functional Materials, EarlyView.Uniaxial strain is demonstrated as a new scheme for a superconductivity switch. Exploiting the large strain‐induced Tc shift in a cuprate superconductor enables robust switching between superconducting and normal states over 100 cycles with only 0.1% strain.
Baizhi Gao +3 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Neuromorphic plasticity in OECTs is governed by the post‐stimulus evolution of coupled ionic and electronic states. Semiconductor chemistry and morphology, electrolyte composition and interfaces, and device architecture regulate ion injection, transport, confinement, and release, shifting responses from rapidly relaxing STP to metastable memory and ...
Inho Lee +9 more
wiley +1 more source
Optimisation of interfacial bond strength of glass fibre endodontic post systems. [PDF]
, 2011 MPhilCurrently endodontically treated teeth are clinically restored using a post and crown system, where the elastic modulus of the post is similar to dentine.
Thanjal, Narinderjeet Tina
core +2 more sources
Ultra‐Thin Tow‐Based Discontinuous Composites—Material Overview and Aspirations
Advanced Functional Materials, EarlyView.Tow‐based discontinuous composites made from ultra‐thin tapes offer outstanding in‐plane mechanical properties. This material, inspired by Nacre, has high volume fraction of tapes exceeding 90 % and allows for quasi‐isotropic material plates less than 100 micrometer in thickness.
Ioannis Katsivalis +8 more
wiley +1 more source