Results 61 to 70 of about 16,379 (267)

Thermal and Performance Analysis of a Photovoltaic Module with an Integrated Energy Storage System

Applied Sciences, 2017
This paper is proposing and analyzing an electric energy storage system fully integrated with a photovoltaic PV module, composed by a set of lithium-iron-phosphate (LiFePO4) flat batteries, which constitutes a generation-storage PV unit.
Manel Hammami, Simone Torretti, Francesco Grimaccia, Gabriele Grandi   +3 more
doaj   +1 more source

Thermal and Electrical Performance of Uncooled, Nature-Cooled, and Photovoltaic Thermal Module

International Journal of Photoenergy, 2023
The experimental study is aimed at analyzing photovoltaic module’s thermal and electrical performance (PV) with back surface cooling under Malaysian tropical climate conditions. The performance of a passively cooled PV module integrated with biomaterial (
Pushpendu Dwivedi, Sujay Ashwinraj Ganesh, Kumarasamy Sudhakar, Archana Soni, S. Shanmuga Priya   +4 more
doaj   +1 more source

Operation Limits of Integrated Photo‐Rechargeable Batteries

Advanced Materials, EarlyView.
This study elucidates the operational limitations of integrated photo‐rechargeable batteries. We demonstrate that the photo‐charging process is fundamentally restricted not only by material‐to‐material energy level alignment but also by transient capacitive charge accumulation within the cathode framework.
Byung‐Man Kim, Arvind Pujari, Hooman Abbasi, Weidong Xu, Yutong Han, Samuel D. Stranks, Michael De Volder   +6 more
wiley   +1 more source

Performance Comparison of Monocrystalline, Polycrystalline, Low Concentrated, and Bifacial PV Modules in a Particular Geographic Location of South India

Energy Science & Engineering
This study presents a performance comparison of four commercially available photovoltaic (PV) modules: polycrystalline PV module (PPVM), monocrystalline PV module (MPVM), low‐concentrated PV module (LPVM), and bifacial PV module (BPVM).
Meenatchi Sundaram Palanisamy, Prince Winston David, Palpandian Murugesan, Praveen Kumar Balachandran, Pravin Murugesan, Muhammad Ammirrul Atiqi Mohd Zainuri, Mattia Braggio, Vigneselvan Sivasubramaniyam   +7 more
doaj   +1 more source

Performance Investigation of Monocrystalline and Polycrystalline PV Modules Under Real Conditions

IEEE Access
Crystalline silicon PV module dominates PV technology worldwide and are constantly emerging with innovative PV designs. Passivated Emitter and Rear Cell PV technology (PERC) is one such high efficiency crystalline PV design that is dominating almost 60 ...
Neha Kumari, Sanjay Kumar Singh, Sanjay Kumar, Vinay Kumar Jadoun   +3 more
doaj   +1 more source

Photocatalytic Water Splitting on the Lunar Surface: Prospects for In Situ Resource Utilization

Advanced Materials Interfaces, EarlyView.
Water has been found in craters on the moon nearby locations which are illuminated >80% of the time. Photocatalysis uses energy from sunlight to drive chemical reactions such as water splitting to produce oxygen and hydrogen. It is a scalable technology that requires lighter equipment and utilizes resources available on the moon. ABSTRACT The discovery
Ranjani Kalyan, Thomas D. Small, Gregory F. Metha, Mahmoud Adel Hamza, Thomas J. O'Dea, Yideng Shen, Cameron J. Shearer   +6 more
wiley   +1 more source

Singapore Modules - Optimised PV Modules for the Tropics

Energy Procedia, 2012
AbstractThe sunbelt regions of the globe on either side of the equator represent a vast potential for the generation of photovoltaic (PV) electricity. However, PV modules deployed in tropical regions face a different set of environmental conditions than PV modules deployed in temperate regions where the majority of today's PV markets exist.
Walsh, Timothy M., Xiong, Zhengpeng, Khoo, Yong Sheng, Tay, Andrew A.O., Aberle, Armin G.   +4 more
openaire   +1 more source

Low‐Temperature Gold Deposition Improves CdTe Back Contacts

Advanced Materials Interfaces, EarlyView.
Cd(Se,Te) samples are cooled during the evaporation of Au back contacts to thermally quench CdTe degradation. Reduced temperature during Au evaporation boosts PV efficiency, open‐circuit voltage, and fill factor. XPS associates these improvements with less chemical perturbation of the CdTe surface during metallization.
Christopher P. Muzzillo, Ryan Muzzio, Craig L. Perkins, B. Edward Sartor, Matthew O. Reese, Chungho Lee   +5 more
wiley   +1 more source

The Evolution of Aerosol Jet Printing, A Review: Enhancing Material Versatility and Improvements for Next‐Generation Applications

Advanced Materials Technologies, EarlyView.
Aerosol Jet Printing (AJP) has emerged as a versatile additive manufacturing technique for high‐resolution, conformal, and multi‐material printing. This review highlights advances in printable materials, substrate compatibility, post‐processing, characterization, and process innovations, while critically discussing current challenges and future ...
Chandrachur Chatterjee, Rocco Lupoi, Michael J. Gibbons   +2 more
wiley   +1 more source

Introducing PNEUMA: A Hybrid Soft Pneumatic Fabric Bidirectional Actuation Module for Wearable Robotics

Advanced Robotics Research, EarlyView.
This study presents a soft pneumatic fabric bidirectional actuation module (PNEUMA) capable of generating high torque in both bending directions within a single integrated architecture. PNEUMA achieves up to 50 Nm with reduced inflation volume and a lightweight design.
Odysseas Simatos, Nikolaos Charalampous, Panagiotis Polygerinos   +2 more
wiley   +1 more source