Results 171 to 180 of about 58,610 (265)

Fully Printed Electrocaloric Heat Pump

open access: yesAdvanced Materials Technologies, EarlyView.
A system based on a flexible printed PEDOT:PSS/P(VDF‐TrFE‐CFE) electrocaloric membrane. The membrane periodically alternates between the cold and hot sides following its electrocaloric cycle and successfully generates a temperature difference. The entire fabrication process is industrially scalable, cost‐effective, and based on widely accessible ...
Adrian Agreda   +7 more
wiley   +1 more source

The Evolution of Aerosol Jet Printing, A Review: Enhancing Material Versatility and Improvements for Next‐Generation Applications

open access: yesAdvanced Materials Technologies, EarlyView.
Aerosol Jet Printing (AJP) has emerged as a versatile additive manufacturing technique for high‐resolution, conformal, and multi‐material printing. This review highlights advances in printable materials, substrate compatibility, post‐processing, characterization, and process innovations, while critically discussing current challenges and future ...
Chandrachur Chatterjee   +2 more
wiley   +1 more source

Waveguide Geometry–Driven Trade‐Offs in Resonant Cavity Sensor Performance

open access: yesAdvanced Optical Materials, EarlyView.
Waveguide geometry governs the interplay between sensitivity, intrinsic Q‐factor, and wavelength noise in silicon nitride resonant sensors. Contrary to intuition, higher sensitivity does not ensure superior performance. Low‐noise, high‐Q ridge resonators achieve the lowest detection limits, revealing that detection is ultimately constrained by noise ...
Mohammad Talebi Khoshmehr   +6 more
wiley   +1 more source

Mono‐ and Bilayer MoS2 Photodetectors: High‐Performance Broadband AC Readout With Color‐Selective Noise Suppression

open access: yesAdvanced Optical Materials, EarlyView.
Mono‐ and bilayer MoS2 photodetectors enable wavelength‐selective AC photoresponse and optically driven capacitance modulation under visible illumination. Green excitation produces the strongest cumulative capacitive response, consistent with trap‐mediated charge accumulation at mono/bilayer and metal–MoS2 interfaces.
Pegah Zandi   +5 more
wiley   +1 more source

Self‐Powered Visible‐Blind Graphene/NiO/ZnO UV‐C Photodiodes

open access: yesAdvanced Optical Materials, EarlyView.
“A scalable architecture for self‐powered UV‐C photodiodes integrates defect‐engineered p‐NiO/n‐ZnO heterojunctions with highly UV‐C transparent graphene anodes. The type‐II band alignment combined with the built‐in electrical field enables robust zero‐bias charge separation.
Umut Kaya   +5 more
wiley   +1 more source

Optical Manipulation of Whispering Gallery Mode Microlasers for Controlled Cellular Delivery

open access: yesAdvanced Optical Materials, EarlyView.
Optically trapped whispering‑gallery microlasers are precisely positioned onto non‐phagocytic mammalian cells to report local refractive‑index changes in real time. Time‑dependent wavelength shifts reveal successive stages from membrane contact to internalization.
Soraya Caixeiro   +3 more
wiley   +1 more source

Learning Highly Dynamic Skills Transition for Quadruped Jumping Through Constrained Space

open access: yesAdvanced Robotics Research, EarlyView.
A quadruped robot masters dynamic jumps through constrained spaces with animal‐inspired moves and intelligent vision control. This hierarchical learning approach combines imitation of biological agility with real‐time trajectory planning. Although legged animals are capable of performing explosive motions while traversing confined spaces, replicating ...
Zeren Luo   +6 more
wiley   +1 more source

Piezoresistivity Enhancement by Graphite Flake Alignment in Thin Composite Films for Dielectric Elastomer Switches

open access: yesAdvanced Robotics Research, EarlyView.
This article presents dielectric elastomer switch (DES) materials, based on composite thin films. Alignment of graphite flakes due to their physical confinement within the thin films lead to much stronger piezoresistive responses than bulk composites, while their durability exceeds that of conventional liquid‐based DES materials.
Lingyu Liu   +3 more
wiley   +1 more source

Auto‐Routing Fluidic Printed Circuit Boards

open access: yesAdvanced Robotics Research, EarlyView.
This work introduces (STREAM) software tool for routing efficiently advanced macrofluidics, an open‐source software tool for automating the design of 3D‐printable fluidic circuit boards. STREAM streamlines tube routing and layout, enabling the rapid fabrication of fluidic networks for soft robotics, lab‐on‐a‐chip devices, microfluidics, and biohybrid ...
Savita V. Kendre   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy