Results 191 to 200 of about 58,192 (289)

Improving efficiency of SMC based IFOC drive for induction motor applying MRAS based adaptive loss model control. [PDF]

Sci Rep
Razani A, Rahbarimagham H, Zeinoddini-Meymand H, Hadi M.   +3 more
europepmc   +1 more source

REACTIVE POWER COMPENSATOR WITH SMOOTH CONTROL

Electrical Engineering and Power Engineering, 2014
V. V. Burlaka, S. V. Gulakov, S. K. Podnebennaya, O. S. Savenko   +3 more
openaire   +2 more sources

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

Advanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht, Alexander Schnettger, Ulrich Holländer, Sven Hübner, Bernd‐Arno Behrens, Hans Jürgen Maier   +5 more
wiley   +1 more source

Particle swarm optimization of synergetic controller and sliding-mode extreme seeking controller for wind power generation system. [PDF]

Sci Rep
Khatir A, Dida A, Babes B, Albalawi F, Awoke YA.   +4 more
europepmc   +1 more source

Interaction of MgO Recyclate‐Based Cermet Anode With KF‐AlF3‐Al2O3 at 800°C During Laboratory Scale Aluminum Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain, Alexander Adamczyk, Felipe Alejandro Garcia Paz, Serhii Yaroshevskyi, Felix Drechsler, Daniel Vogt, Christos G. Aneziris, Alexandros Charitos   +7 more
wiley   +1 more source

An optimal multi-objective control architecture of PMSM drives. [PDF]

Sci Rep
Mohapatra BK, Sharma V, Bhowmik P, Mishra R.   +3 more
europepmc   +1 more source

Toward Low‐Consumable Anodes: Process Simulation and Prospective Life Cycle Assessment of NiFe2O4‐NiO‐Ni‐Cu vs. Prebaked Anodes for Aluminum Production with use of Molten Salt Electrolysis

Advanced Engineering Materials, EarlyView.
Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz, Ulziikhuu Otgonbayar, Alexander Adamczyk, Farhan Hossain, Daniel Vogt, Johan Berg Pettersen, Alexandros Charitos   +6 more
wiley   +1 more source

Performance measurement of high gain Landsman converter with ANFIS based MPPT and cascaded H-bridge thirty-one multilevel inverter in a single-phase grid-connected PV system. [PDF]

Sci Rep
Kumar NB, M UMR, Lakshminarayana P, Rao CNN, Veeranjaneyulu J.   +4 more
europepmc   +1 more source

Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories

Advanced Engineering Materials, EarlyView.
Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov, Eldar Salpagarov, Anhelina Mospan, Till Manon Jannis Stadtmüller, Thomas Schemmel, Christos Georgios Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Fuzzy-logic-controlled DVR for enhancing the fault resilience of wind energy conversion systems. [PDF]

Sci Rep
Nori AM, Abdulabbas AK, Al Garni HZ, Mbasso WF, Alruwaili M, ELrashidi A.   +5 more
europepmc   +1 more source