Results 71 to 80 of about 44,651 (286)

On the WEDM of WNbMoTaZr_x (x = 0.5, 1) Refractory High Entropy Alloys

Entropy, 2022
As a potential candidate for the next generation of high-temperature alloys, refractory high entropy alloys (RHEAs) have excellent mechanical properties and thermal stability, especially for high-temperature applications, where the processing of RHEAs ...
Shunhua Chen, Kuang Xu, Weijie Chang, Yong Wang, Yucheng Wu   +4 more
doaj   +1 more source

Effects of process parameters of fast EDM drilling on the recast layer

The International Journal of Advanced Manufacturing Technology
Abstract Fast EDM (electrical discharge machining) drilling is widely used in the machining of film cooling holes of aero-engine turbine blades. However, the EDM process will produce a recast layer, which will affect the surface performance of blades.
Xue-Cheng Xi, Hao-Yu Chu, Bin Li, Wan-Sheng Zhao   +3 more
openaire   +1 more source

Shear flow-interchange instability in nightside magnetotail causes auroral beads as a signature of substorm onset

, 2019
A geometric wedge model of the near-earth nightside plasma sheet is used to derive a wave equation for low frequency shear flow-interchange waves which transmit $\vec{E} \times \vec{B}$ sheared zonal flows along magnetic flux tubes towards the ionosphere.
Derr, Jason, Horton, Wendell, Wolf, Richard   +2 more
core   +1 more source

Digital Surface‐Enhanced Raman Scattering With Event Counting and Spectrum Learning for Label‐Free Protein Quantification

Advanced Intelligent Systems, EarlyView.
A statistical and machine learning‐assisted surface‐enhanced Raman scattering (SERS) framework is developed for label‐free quantification of low‐abundance analytes, including proteins. Combining digital SERS event counting with binomial regression and an artificial neural network (ANN) trained on full spectra, the approach achieves picomolar detection ...
Eni Kume, James Rice
wiley   +1 more source

Optimizing the Die-Sink EDM Machinability of AISI 316L Using Ti-6Al-4V-SiCp Electrodes: A Computational Approach

Journal of Manufacturing and Materials Processing
Die-sink electric discharge machining (EDM) is essential for shaping complex geometries in hard-to-machine materials. This study aimed to optimize key input parameters, such as the discharge current, gap voltage, pulse-on time, and pulse-off time, to ...
Adithya Hegde, Raviraj Shetty, Rajesh Nayak, Sawan Shetty, Uday Kumar Shetty SV   +4 more
doaj   +1 more source

Modelling and optimization of Chromium Powder Mixed EDM Parameter Effect Over the Surface Characteristics by Response Surface Methodology Approach

International Journal of Engineering Materials and Manufacture, 2018
In this paper, an optimization of chromium powder mixed parameters effect, i.e. discharge current, pulse on time and Cr powder concentration of AISI D2 steels in Powder Mixed EDM (PMEDM) has been made.
Nor Ain Binti Jamil Hosni, Mohd Amri Bin Lajis, Muhammad Ridzuan Bin Idris   +2 more
doaj   +1 more source

Modified CNTs/Nafion composite: The role of sulfonate groups on the performance of prepared proton exchange methanol fuel cell’s membrane [PDF]

Journal of Particle Science and Technology, 2017
A novel Nafion®-based nanocomposite membrane was synthesized to be applied as direct methanol fuel cells (DMFCs). Carbon nanotubes (CNTs) were coated with a layer of silica and then reacted by chlorosulfonic acid to produce sulfonate-functionalized ...
Kamran Janghorban, Payam Molla-Abbasi
doaj   +1 more source

Investigation of recast and crack formation in laser trepanning drilling of CMSX-4 angled holes [PDF]

, 2018
This paper presents an experimental investigation on the influences of laser trepanning drilling process parameters on the recast layer thickness and surface crack formation in CMSX-4 nickel-based superalloy angled holes. The effects of peak power, pulse
A Corcoran, A Corcoran, A Horn, BS Yilbas, C Yeo, CA McNally, DKY Low, E Lugscheider, EW Kreutz, H Sezer, J Garofano, J Garofano, J Willach, John Nicholls, Jörn Mehnen, K Voisey, KPL Fullagar, M Schneider, M Schneider, ND Pandey, Nicolau Iralal Morar, PW French, R Bathe, R Goyal, Rajkumar Roy, S Bandyopadhyay, S Dimov, S Kumar, S Leigh, S Leigh, S Mishra, S Tam, Simon Gray, Sundar Marithumu, T Beck, Tracey Roberts, W Duan, WT Chien   +37 more
core   +1 more source

Participatory Policy Development: Reflections on Designing the Strong Roots for Our Futures Program in Victoria

Australian Journal of Social Issues, EarlyView.
ABSTRACT In this paper, we trace the journey to create the Strong Roots for our Futures Program, a government program to resource and support Traditional Owners to undertake a range of activities in areas where no state recognition existed. We provide a background to state recognition in Victoria before considering the program design, leading to an ...
Nell Reidy, Bhiamie Williamson, Jesse Williams   +2 more
wiley   +1 more source

Effect of different tool materials during EDM performance of titanium grade 6 alloy

Engineering Science and Technology, an International Journal, 2018
During this investigation, a comparative study has been carried out on electro discharge machining (EDM) of titanium grade 6 alloy using different type of electrodes viz. copper, brass and zinc.
Munmun Bhaumik, Kalipada Maity
doaj   +1 more source