Results 11 to 20 of about 451,301 (380)
Hydrometallurgical refining of metallurgical silicon
Izvestiya. Ferrous Metallurgy, 2023 The paper presents the results of refining silicon of metallurgical grades based on leaching of impurities with inorganic acids. Silicon samples were studied by metallographic and X-ray fluorescent methods of analysis, as well as X-ray spectral ...
Н. В. Немчинова +2 more
openalex +3 more sources
Archives of Metallurgy and Materials, 2023 It is really hard to determine the phenomena occurring during aluminum refining process using argon blowing through the liquid metal in industrial conditions. The solution of such problem is physical modelling. This kind of modelling gives possibility to
M. Saternus
semanticscholar +1 more source
Experimental and numerical modelling of mass transfer in a refining ladle
Metallurgical Research and Technology, 2022 Mass transfer between liquid steel and slag is an important physical phenomenon during secondary metallurgy for prediction of the chemical reaction rate and adjustment of liquid steel composition.
Nelson Joubert +3 more
semanticscholar +1 more source
Advances in Understanding of the Application of Unit Operations in Metallurgy of Rare Earth Elements
Metals, 2021 Unit operations (UO) are mostly used in non-ferrous extractive metallurgy (NFEM) and usually separated into three categories: (1) hydrometallurgy (leaching under atmospheric and high pressure conditions, mixing of solution with gas and mechanical parts ...
S. Stopić, B. Friedrich
semanticscholar +1 more source
PHASE FORMATION DURING STEEL REFINING BY ALLOYS WITH ALKALINE EARTH ELEMENTS (Ba, Mg, Sr)
Ferrous Metallurgy. Bulletin of Scientific , Technical and Economic Information, 2022 Important factors affecting the quality of steel are both the level of metal contamination with non-metallic inclusions and the properties of these inclusions.
L. Makrovets +2 more
semanticscholar +1 more source
Sulaimani Journal for Engineering Sciences, 2015 In this study Al - (0-15 wt %) Y2O3 composites were prepared by both squeeze casting and powder metallurgy routes. It was found throughout this work that Vickers microhardness, compressive yield strength and wear resistance increase continuously with ...
Farouk M. Mahdi, Abd-Ulkader A. Annaz
doaj +1 more source
Innovative Development of Low-Carbon, Clean, and Intelligent Aluminum Metallurgy [PDF]
中国工程科学Aluminum is the most widely used non-ferrous metal. Promoting the low-carbon, clean, and intelligent development of the aluminum metallurgy is crucial for implementing the new development philosophy and cultivating new quality productive forces.
Jie Li +6 more
doaj +1 more source
Grain Refinement of Ti-15Mo-3Al-2.7Nb-0.2Si Alloy with the Rotation of TiB Whiskers by Powder Metallurgy and Canned Hot Extrusion [PDF]
Metals, 2020 In situ synthesized TiB whiskers (TiBw) reinforced Ti-15Mo-3Al-2.7Nb-0.2Si alloys were successfully manufactured by pre-sintering and canned hot extrusion via adding TiB2 powders. During pre-sintering, most TiB2 were reacted with Ti atoms to produce TiB. During extrusion, the continuous dynamic recrystallization (CDRX) of β grains was promoted with the
Jiabin Hou +5 more
openaire +2 more sources
Archaeology, science-based archaeology and the Mediterranean Bronze Age metals trade [PDF]
, 2000 Archaeologists often seem either sceptical of science-based archaeology or baffled by its results. The underpinnings of science-based archaeology may conflict with social or behavioural factors unsuited to quantification and grouping procedures.
Knapp, A.B.
core +1 more source
Factors influencing power consumption and power-saving measures in ESR process [PDF]
China Foundry, 2019 Since the USA patent of electroslag remelting (ESR) metallurgy was held by P. K. Hopkins in 1940, the ESR technology has now entered a relatively mature stage after a 70-year history of development.
Yun-Long Xiong +2 more
doaj +1 more source