Results 61 to 70 of about 3,653 (237)

Higher representation Wilson lines in SU(2) lattice gauge theory

Physics Letters B, 1988
Abstract The temperature dependence of higher representation Wilson lines L j is investigated in SU(2) gauge theory on an 183×4 lattice. We show that in the region immediately above deconfinement, the behaviour of the fundamental ( j= 1 2 ), the adjoint (j=1) and the ( j= 3 2 Wilson lines are wel parametrized by the form L
REDLICH, K, Satz, Helmut
openaire   +1 more source

Elastic Properties and Thermal Expansion Behavior of a Polycrystalline VMnFeCoNi High‐Entropy Alloy

Advanced Engineering Materials, EarlyView.
The high‐entropy alloy (HEA) V20Mn20Fe20Co20Ni20 (composition in at.%) can be made single‐phase face‐centered cubic (FCC) when annealed above 1338 K followed by water quenching. In this state, the alloy exhibits the greatest strength‐ductility combination of any quinary single‐phase FCC HEA.
Guillaume Laplanche, Marie Münchhalfen, Aditya Srinivasan Tirunilai, Jürgen Schreuer   +3 more
wiley   +1 more source

Frequency-dependent topology in multisublattice systems: Analytical theory of dispersive effective Hamiltonians

Physical Review Research
Topological phases in one-dimensional lattices are usually described by fixed, frequency-independent Hamiltonians, where topology is determined solely by structural parameters.
Seiji Mizuno
doaj   +1 more source

Visualization-driven physics-informed modeling of energetics with demonstrated transfer between configurationally isomorphic substitutional alloys

Results in Physics
Substitutional alloys pose a fundamental challenge for first principles modeling because the number of distinct chemical configurations grows combinatorially with system size.
Gholamhosain Haidari, Zahra Mosleh
doaj   +1 more source

Foundational Machine‐Learning Interatomic Potential for Simulating Chemically Complex Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
We apply a foundational machine‐learning interatomic potential based on the graph atomic cluster expansion (GRACE) to simulate the commercial Ni‐based single‐crystal superalloy CMSX‐4. Hybrid Monte‐Carlo/molecular dynamics sampling resolves short‐range order in the γ phase and L12 sublattice occupancies in the γ’ phase and connects them to stacking ...
Aditya Vishwakarma, Sarath Menon, Fritz Körmann, Thomas Hammerschmidt, Ralf Drautz   +4 more
wiley   +1 more source

Representation theory for dilute lattice models

, 2004
LaTeX, 16 pages, no ...
openaire   +2 more sources

Uniform Amorphization of Crystalline Silicon Surfaces Enabled by Deep Ultraviolet Femtosecond Laser Pulses

Advanced Engineering Materials, EarlyView.
Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali, Magali Gregoire, Matys Guyard, Tatiana Itina, David Grojo, Pol Sopeña   +5 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source