Results 161 to 170 of about 277 (206)
steel research international, EarlyView.Paint baking of resistance spot welded joints of 2.0 GPa warm‐stamped medium‐Mn steel activates low‐temperature tempering, forming fine cementite in the fusion zone and enhancing toughness. Crack propagation resistance increases, shifting the failure mode from partial interfacial to complete pullout, with peak load and energy absorption rising ...
Sunusi Marwana Manladan +8 more
wiley +1 more source
Identification of the Cohesive Parameters for Modelling of Bonded Joints between Flat Composite Adherends with Thick Layer of Adhesive. [PDF]
Materials (Basel)Bernardin P +4 more
europepmc +1 more source
steel research international, EarlyView.An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén +3 more
wiley +1 more source
steel research international, EarlyView.The high‐strain‐rate behavior of resistance spot‐welded DP800–DP1000 joints is investigated. Results show that microstructural gradients across BM–HAZ–FZ govern hardness, strain rate sensitivity, and failure modes. While strength increases with strain rate, energy absorption is controlled by ductility, with DP800–DP800 joints showing superior ...
Pankaj Shrivastava, Velaphi Msomi
wiley +1 more source
steel research international, EarlyView.Tailored heat treatments transform additively manufactured high‐nitrogen martensitic Cr steel from austenitic as‐built condition to high‐hardness states. Isothermal bainitizing at 250°C generates an ultrafine nanostructure and achieves higher hardness than conventional hardening and tempering, highlighting a promising postprocessing route for laser ...
Philip König +2 more
wiley +1 more source
steel research international, EarlyView.This review's second part details the mechanical, corrosion, and electromagnetic behaviors of FSSs. It integrates the foundational microstructure (texture/defects/precipitates) and processing effects from Part I to establish and analyze complex property–property interrelationships critical for high‐performance applications.
Shahab Bazri +2 more
wiley +1 more source
Structural Concrete, EarlyView.Abstract Precast reinforced concrete segmental linings are frequently used in modern tunneling. In these linings, the longitudinal joints typically have a reduced contact cross‐section and thus often govern the design, particularly in tunnels under high hydrostatic pressure or crossing squeezing or swelling ground with correspondingly high ...
Fabian Morger +2 more
wiley +1 more source
Structural Concrete, EarlyView.Abstract With the market introduction of new reinforcing materials, such as corrosion‐resistant steel, the effect of their stress–strain relationship on the ductility of reinforced concrete structures needs to be evaluated. Their moment‐curvature behavior significantly influences bending moment redistributions, rotation capacity, and deformation at ...
Nathalie Reckinger +2 more
wiley +1 more source
Split‐disk testing of precast ultra‐high performance fiber‐reinforced concrete tubes
Structural Concrete, EarlyView.Abstract Ultra‐high performance fiber‐reinforced concrete (UHPFRC) has great potential for structural applications involving precast cylindrical shapes, including pipes, silos and stay‐in‐place forms for concrete columns. This study examines the performance of UHPFRC rings under internal pressure simulated using the split‐disk loading method, along ...
Mina Fakeh, Amir Fam
wiley +1 more source
Impact Strength of Adhesive Joints of Pre-Impregnated Composite Elements. [PDF]
Materials (Basel)Komorek A, Żeglarski P, Godzimirski J.
europepmc +1 more source