Results 181 to 190 of about 105,821 (276)

Strain Development During Cure of Partially Pre‐Cured Thermosetting Composites Measured With Distributed Fiber Optic Sensors

Polymer Composites, EarlyView.
Schematic representation of the beneficial effect of ply pre‐curing on temperature overshoot, internal strain and warpage during cure of thin and thick thermosetting composites. ABSTRACT Detection of manufacturing‐induced defects in thermosetting composites is crucial to guarantee part quality, safety, and improve manufacturing efficiency.
Francesco Taddei, Giacomo Struzziero, Valentin Ott, Véronique Michaud   +3 more
wiley   +1 more source

<i>In Situ</i> Multiscale Investigation of Capillary-Force-Induced Cold-Welding of Silver Nanowire Networks. [PDF]

ACS Omega
Chernukha Y, Bardet L, Berthe M, Lerond T, Mazellier JP, Gangloff L, Denneulin A, Diener P, Bellet D.   +8 more
europepmc   +1 more source

Effect of Consolidation Time in Hot Press Compression Molding of Continuous Carbon Fiber‐Reinforced Polyetheretherketone Composite

Polymer Composites, EarlyView.
Influence of consolidation time on interlaminar shear strength and void content after hot press consolidation and vacuum bag only processes. ABSTRACT Processing long fiber reinforced thermoplastic composites such as polyaryletherketones with carbon fibers (CF/PEEK) has found interest in the aerospace industry due to short‐time manufacturing and ...
Adrian Korycki, Fabrice Carassus, Christian Garnier, France Chabert, Toufik Djilali   +4 more
wiley   +1 more source

Advances in Welding Process and Materials. [PDF]

Materials (Basel)
Codrean C, Opriș C, Feier A.
europepmc   +1 more source

Recyclability of Polystyrene Bead Foams: Degradation Behavior over 10 Extrusion Cycles

Polymer Engineering &Science, EarlyView.
This study investigates the multi‐cycle recycling of expanded polystyrene bead foam blended with virgin material. Material degradation is monitored by MFI, GPC, and mechanical testing. The results demonstrate that long‐term recyclability is feasible without progressive property loss, and that secondary high‐shear steps such as extrusion and pelletizing
Christian Töpfer, Kristina Schüllner, Holger Ruckdäschel   +2 more
wiley   +1 more source

Analysis of Thick-Walled Oxygen-Free Copper Pipe Production in the Bridge Die Extrusion Process. [PDF]

Materials (Basel)
Knapiński M, Banaszek G, Kawałek A, Bajor T, Boczkal G.   +4 more
europepmc   +1 more source

Characteristics, properties and limitations of per‐ or polyfluoroalkyl substances (PFASs) and fluoropolymers

Polymer International, EarlyView.
An overview and categorization of man‐made per‐ or polyfluoroalkyl substances (PFASs) including low‐molar‐mass and high‐molar‐mass fluorochemicals, and their international regulations is presented. Though certain PFASs are toxic, bioaccumulative and cross the human cellular membranes, others, such as fluoropolymers, are safe, reliable and involved in ...
Bruno Améduri
wiley   +1 more source

Properties and Microstructure Evaluation of Laser-Welded TP347-TP904L High-Alloy, Stainless Steels Joints, Modified with 309L Filler. [PDF]

Materials (Basel)
Danielewski H, Kurp P, Skrzypczyk A, Kozák J, Konopík P, Yao J, Zhang Q, Rzepa S.   +7 more
europepmc   +1 more source

Tuning the Morphology of Self‐Assembled Nanopatterns on MgO(001) Surfaces by Sequential Broad‐Beam Ion Irradiation

physica status solidi (RRL) – Rapid Research Letters, EarlyView.
A two‐step approach based on broad‐beam ion irradiation is demonstrated to produce fine‐tuned self‐assembled surface patterns on MgO(001). It shows an efficient route to modifying the crystalline MgO(001) surface topography in a controlled way, making use of its very specific behavior in terms of both the pattern morphology and patterning dynamics.
Denise J. Erb, Stefan Facsko
wiley   +1 more source

Investigating the Effects of Iron Dilution on the Corrosion Resistance of Inconel 625 Welding Overlay on Carbon Steel. [PDF]

Materials (Basel)
Cunha AB, Vatavuk J, Lima CRC.
europepmc   +1 more source