Results 221 to 230 of about 178,886 (297)

Digital Versus Conventional Splints in Patients With Temporomandibular Disorders: A Systematic Review and Meta-Analysis of Randomized Controlled Trials. [PDF]

Cureus
Almansour FW, Alshammari K, Mohammed Alhajri D, Bader Alzamanan M, Hamed Alduaij F, Walled Abdullah K, Homoud Alnoumas M, Abdelaziz A.   +7 more
europepmc   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Comparison of point-of-care HbA1c devices with laboratory HPLC methods: A systematic review and meta-analysis. [PDF]

Biomed Rep
Wei Y, Gu M, Ren Y, Hu Z.
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

REML — a program for the analysis of non-orthogonal data by restricted maximum likelihood

, 1982
Digby, P. G. N., Robinson, D. L., Thompson, R.   +2 more
core  

dynConfiR: An R package for sequential sampling models of decision confidence. [PDF]

Behav Res Methods
Hellmann S, Zehetleitner M, Rausch M.
europepmc   +1 more source

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

Association Between SGLT2 Inhibitor Use and Hepatocellular Carcinoma Risk in Type 2 Diabetes: A Systematic Review and Meta-Analysis. [PDF]

Biomedicines
Hu JH, Chang ML, Huang TJ, Liu NJ, Tang JH.   +4 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Intensified blood pressure control during hospital admission and on discharge: a systematic review and meta-analysis of retrospective cohort studies. [PDF]

Front Cardiovasc Med
Kushnir Y, Barrera N, Arias-Sanchez P, Romero E, Statnii I, Stolear A, Golovataya K, Solorzano MF, Baghdadi S, Shkolnik E.   +9 more
europepmc   +1 more source