Results 31 to 40 of about 4,495 (247)

Copper Nanocrystallization in Anodic Oxide Films of Ti–Cu‐Based Bulk Metallic Glass and Its Effect on the Corrosion Resistance and Cytocompatibility

Advanced Engineering Materials, EarlyView.
Viktoriia Shtefan, Thorgund Nemec, Ute Hempel, Annett Gebert and coworkers demonstrate that anodic treatment of Ti–Cu‐based metallic glass in a nontoxic pyrophosphate electrolyte forms a protective bilayered Ti/Zr‐oxide film enriched with Cu nanocrystals.
Viktoriia Shtefan, Nora Fernández Navas, Thorgund Nemec, Ivan Kaban, Ute Hempel, Andrea Voss, Volker Hoffmann, Darius Pohl, Annett Gebert   +8 more
wiley   +1 more source

Studies on the Influence of Residual Stresses on the Fatigue Life of Rolling Bearings in Dependence on the Production Processes

Frontiers in Mechanical Engineering, 2020
The production process significantly influences the surface properties of rolling element bearings raceways. Deep rolling can induce a depth dependent residual stress state.
Florian Pape, Timm Coors, Gerhard Poll
doaj   +1 more source

Influence of Surface Finish on the Tribological Performance of AlTiBN Coatings Deposited on Forming Tools

Advanced Engineering Materials, EarlyView.
Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver, Iker Alfonso, Eneko Barba, Javier León, José Antonio García, Iñaki Zalakain, Iván Fernández Martínez, Arley García‐Carrero, Christian Almeyda, Daniel Salcedo   +9 more
wiley   +1 more source

Research on Key Technologies of Temperature Rise Suppression for Motor Grease Lubricated Rolling Bearing

机车电传动, 2020
At present, grease lubrication is widely used in motor rolling bearings. However, the bearing DN value increases rapidly with the increasing of motor speed and power for the factor that the lubricating grease is semi-solid with poor flow and heat ...
Baoying SHE, Sizhou GUO, Ronghai MEI, Haijiang LI, Jiawei CAO   +4 more
doaj  

Substrate Stress Relaxation Regulates Cell‐Mediated Assembly of Extracellular Matrix

Advanced Functional Materials, EarlyView.
Silicone‐based viscoelastic substrates with tunable stress relaxation reveal how matrix mechanics regulates cellular mechanosensing and cell‐mediated matrix remodelling in the stiff regime. High stress relaxation promotes assembly of fibronectin fibril‐like structures, increased nuclear localization of YAP and formation of β1 integrin‐enriched ...
Jonah L. Voigt, Jens Timmer, Elisabetta Ada Cavalcanti‐Adam   +2 more
wiley   +1 more source

Transient Simulation Analysis of Needle Roller Bearing in Oil Jet Lubrication and Planetary Gearbox Lubrication Conditions Based on Computational Fluid Dynamics

Lubricants
The transient lubrication conditions of rolling bearings are different in gearboxes and bearing testers. It has been observed that samples of qualified rolling bearings tested in rolling bearing testers often fail and do not meet lifespan requirements ...
Shushen Gao, Xiangying Hou, Chenfei Ma, Yankun Yang, Zhengminqing Li, Rui Yin, Rupeng Zhu   +6 more
doaj   +1 more source

3D‐Printed Sulfur‐Derived Polymers With Controlled Architectures for Lithium‐Sulfur Batteries

Advanced Functional Materials, EarlyView.
Rheology‐guided formulation design for direct ink writing enables the fabrication of 3D sulfur copolymer cathodes with controlled architectures for lithium‐sulfur batteries. The printed electrodes exhibit multiscale porosity and high sulfur utilization, delivering enhanced electrochemical performance compared to conventional cast electrodes.
Bin Ling, Haoran Wang, Pan Yang, Rishav Agrawal, Alex R. Neale, Laurence J. Hardwick, Tom Hasell, Esther García‐Tuñón   +7 more
wiley   +1 more source

Fault Diagnosis for Rolling Bearings Using Optimized Variational Mode Decomposition and Resonance Demodulation

Entropy, 2020
It is difficult to extract the fault signal features of locomotive rolling bearings and the accuracy of fault diagnosis is low. In this paper, a novel fault diagnosis method based on the optimized variational mode decomposition (VMD) and resonance ...
Chunguang Zhang, Yao Wang, Wu Deng
doaj   +1 more source

Understanding the Role of Superhydrophobicity and Superhydrophilicity in Salt‐Spray Corrosion of Nanosecond Pulsed Laser‐Textured AA2024 Alloy

Advanced Functional Materials, EarlyView.
Nanosecond pulse laser texturing yields superhydrophobic and superhydrophilic AA2024 surfaces. Salt‐spray tests show that periodic superhydrophobic patterns suppress pitting, whereas superhydrophilic textures enhance it, linking laser‐induced morphology, wettability, and oxide chemistry to corrosion resistance.
Lis Geraldine Zschach, Robert Baumann, Eric Pohl, Angelika Wrzesińska‐Lashkova, Marcelo Sallese, Ignacio Tabares, Herman Heffner, Yana Vaynzof, Andrés Fabián Lasagni   +8 more
wiley   +1 more source

Fault Diagnosis of Rolling Bearing Based on a Novel Adaptive High-Order Local Projection Denoising Method

Complexity, 2018
Rolling bearings are vital components in rotary machinery, and their operating condition affects the entire mechanical systems. As one of the most important denoising methods for nonlinear systems, local projection (LP) denoising method can be used to ...
Rui Yuan, Yong Lv, Gangbing Song
doaj   +1 more source