Results 11 to 20 of about 1,121 (250)
THE EFFECT OF WELDING FRICTION PARAMETERS ON THE MECHANICAL PROPERTIES OF THE MAINTAINED ANODIC YOK IN THE ALUMINUM INDUSTRY [PDF]
Journal of the Egyptian Society of Tribology, 2023 In this paper, friction welding was applied in the aluminum industry at repairing operation. The process of repairing the anodic yoke, which was carried out by welding in the traditional way, was replaced by the method of rotary friction welding, as a ...
Zayed Safwt +4 more
doaj +1 more source
Design and Dynamic Characteristics Analysis of Rotating Welding Torch with Ball Joint Type Mechanical Seal structure [PDF]
한국정밀공학회지, 2023 This paper proposes a new rotary welding torch with a ball-jointed mechanical seal structure that simultaneously realizes the enclosure of CO2 gas, the energization of welding current, and the insulation for system protection.
Dong Jun Lee +3 more
doaj +1 more source
Multi-Objective Optimisation of Welding Parameters for AZ91D/AA6082 Rotary Friction Welded Joints
Applied SciencesRecently, rotary friction welding has been used to join magnesium alloys. FRW uses friction heat to bond magnesium alloys with aluminium alloys. Combining these light alloys can provide many promising applications in the industry.
Radosław Winiczenko +2 more
doaj +2 more sources
Effect of Friction Stir Welding Parameters on Welding Joint Characteristics : A review [PDF]
SVU-International Journal of Engineering Sciences and Applications, 2023 Friction stir welding (FSW) has been used to join metallic and non-metallic materials without melting the base metal. this process employs a non-consumable rotary welding tool consist of a shoulder and a pin.
Qays Ismael, Mohmmed Fathi, Zenaa Abid
doaj +1 more source
Journal of Manufacturing and Materials Processing, 2022 Due to the different properties of the materials, the fusion welding of dissimilar metals may be difficult. Structural irregularities may form as a result of various phase transformations during welding. Solid-state welding, as opposed to fusion welding,
Hudiyo Firmanto +4 more
doaj +1 more source
Rotary Friction Welding of Molybdenum without Upset Forging [PDF]
Materials, 2020 A large instantaneous axial forging load is required to be applied for the final stage of rotary friction welding (RFW), which is usually conducive to obtaining clean, compact, and high-quality joints. However, for slender fuel claddings made of molybdenum (Mo) with low stiffness, the instantaneous axial forging load cannot be applied at the final ...
Miaoxia Xie +5 more
openaire +2 more sources
The Influence of Different Wood Modifications on Pull-out Force of Rotary Welded Dowels
Drvna Industrija, 2023 The increasing use of modified wood justifies the intention to use it in joints made by rotary welding with dowels. Thermal modification, for example, increases the dimensional stability of wood by reducing its hygroscopicity and water absorption, but it
Ivica Župčić +4 more
doaj +1 more source
Dependence of Dowel Joint Strength on Welding Temperature in Rotary Welding
Drvna industrija, 2021 The system for measuring the welding temperature with measuring probes has been developed for the requirements of this but also of future research (at the Faculty of Forestry and Wood Technology, University of Zagreb). The research is based on determining the welding temperature and its impact on the joint strength or the embedded force of the dowel ...
Župčić, Ivica +3 more
openaire +2 more sources
Fabrication of Motorized Rotary Welding Table
, 2023 {"references": ["Vijaykumar, P., Varsan, M.M., et al. (2022). Design and fabrication of Automatic Welding table. International Journal of Research Publication and Reviews, 3(5), 778-784.", "Kamesh, S., Karthik, M., et al. (2021). 360\u00b0 Welding cutting rotary turn table positioner. International Research Journal of Engineering and Technology (IRJET),
Ch Ranga Rao +5 more
openaire +1 more source
Experimental Investigation of AA6063 Welded Joints Using FSW
Advances in Materials Science and Engineering, 2022 The AA6063 aluminium alloy has gained widespread use in manufacturing the light-weighted structures which requires a high strength to weight ratio, and it possesses an excellent corrosive resistance in T6 heat-treated (solution heat treated and ...
T. Rajkumar +4 more
doaj +1 more source