Results 51 to 60 of about 337,376 (283)
Bio‐Inspired Artificial Ionic Mechanoreceptor
Advanced Functional Materials, EarlyView.A skin‐inspired artificial mechanoreceptor based on ionic interactions is presented for biomimetic tactile sensing. Pressure‐driven ionic redistribution within microfluidic channels generates a self‐powered electrical signal without external bias. The generated waveform exhibits mechanoreceptor‐like temporal features, including overshoot and undershoot,
Mohammad Akbari +4 more
wiley +1 more source
A New Method for Adjusting Setting Angle of Rotor Blade for Axial Fan in Wind Tunnel
Xibei Gongye Daxue Xuebao, 2019 Combining the fan aerodynamic efficiency with the wind tunnel pressure loss coefficient, a new equation which points out the inherent relationship of the fan blade setting angle, fan rotating speed and gas flow rate in wind tunnel circuit is derived ...
doaj +1 more source
Applied Sciences, 2023 A new method for the synchronous vibration parameter identification of constant-speed rotating blades based on blade tip clearance (BTC) measurement and blade tip timing (BTT) is introduced.
Liang Zhang +4 more
doaj +1 more source
Advanced Functional Materials, EarlyView.A sequential dual‐alignment strategy independently programs the orientation of conductive metal‐organic framework (c‐MOF) microrods and liquid crystals within a composite film. This approach creates an asymmetric bilayer structure that enables precise, multi‐responsive actuation.
Taegyun Hong +5 more
wiley +1 more source
Applied Sciences, 2023 Individual pitch control (IPC) is a method to mitigate periodic blade loads in wind turbines, and it is typically implemented using the multi-blade coordinate (MBC) transform, which converts the blade load measurements from a rotating frame into the non ...
Manuel Lara +4 more
doaj +1 more source
Advanced Functional Materials, EarlyView.A hybrid additive manufacturing platform integrates direct droplet writing of metallic composite with VAT photopolymerization to fabricate architected soft magnetic composites. This approach enables microscale patterning of high‐viscosity materials for programmable actuators, adaptive fluidic devices, and switchable adhesives, offering tunable ...
Yeowon Yoon +4 more
wiley +1 more source
Heat transfer on a film-cooled rotating blade [PDF]
International Journal of Heat and Fluid Flow, 1999 A multi-block, three-dimensional Navier-Stokes code has been used to compute heat transfer coefficient on the blade, hub and shroud for a rotating high-pressure turbine blade with 172 film-cooling holes in eight rows. Film cooling effectiveness is also computed on the adiabatic blade. Wilcox’s k-ω model is used for modeling the turbulence. Of the eight
openaire +1 more source
Advanced Functional Materials, EarlyView.Keratin recovered from animal‐hair textile waste is fractionated and blended with cellulose to produce continuously spun hybrid fibers. Selecting the high‐molecular‐weight keratin fraction enables 30 wt.% keratin incorporation while maintaining high strength in dry and wet states.
Mian Zhai +6 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A spatial location of atomic layer deposition (ALD)‐derived ZrO2 coatings is demonstrated to be a critical design parameter for stabilizing graphite cathodes in DIBs. Direct particle‐level ALD (PALD) screening of representative metal oxides identified ZrO2 as the coating that provides the most favorable balance of high‐rate capability and interfacial ...
Jieun Kang +7 more
wiley +1 more source
Shock and Vibration, 2021 Blade tip-timing is one of the most effective methods for blade vibration parameters identification of turbomachinery. Once-per revolution (OPR) sensor is usually used to determine the rotating speed and as a time reference. However, the OPR sensor leads
Liang Zhang, Huiqun Yuan, Xin Li
doaj +1 more source