Results 101 to 110 of about 27,076 (290)
Engineering Science and Technology, an International JournalThe machining of slots in aeronautical turbine cases and discs is an extremely delicate operation. First, these parts require materials with excellent wear, high temperature and corrosion properties, such as the low machinability materials of the S group.
Pablo Fernández-Lucio +3 more
doaj +1 more source
Design and Implementation of a System-on-Chip for Self-Calibration of an Angular Position Sensor
Applied Sciences, 2019 In this study, a novel signal processing algorithm and hardware processing circuit for the self-calibration of angular position sensors is proposed. To calibrate error components commonly found in angular position sensors, a parameter identification ...
Zhenyi Gao +6 more
doaj +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Improved rounding for spline coefficients and knots [PDF]
, 1994 When representing the coefficients and knots of a spline using only small integers, independently rounding each infinite-precision value is not the best strategy.
Eric Grosse, John D. Hobby
core +1 more source
Advanced Engineering Materials, EarlyView.Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley +1 more source
Dinamika Rekayasa, 2006 Column calculation on frame system is a long and iterative process. This program is used to calculate column on general aspects, these aspects are slender, biaxial, braced frame and sway frame. This program uses Borland Delphi 7.0 language.
Bagyo Mulyono
doaj
Atmospheric and Oceanic Science Letters, 2017 The computational uncertainty principle states that the numerical computation of nonlinear ordinary differential equations (ODEs) should use appropriately sized time steps to obtain reliable solutions.
Jing CAO, Jian-Ping LI, Xin-Yuan ZHANG
doaj +1 more source
Advanced Engineering Materials, EarlyView.We apply a foundational machine‐learning interatomic potential based on the graph atomic cluster expansion (GRACE) to simulate the commercial Ni‐based single‐crystal superalloy CMSX‐4. Hybrid Monte‐Carlo/molecular dynamics sampling resolves short‐range order in the γ phase and L12 sublattice occupancies in the γ’ phase and connects them to stacking ...
Aditya Vishwakarma +4 more
wiley +1 more source