Results 191 to 200 of about 100,180 (302)

Rubber snow interface and friction

, 2014
Tyres are used in everyday life for a variety of practical and recreational tasks. Frictional behaviour of tyres on any surface is important for vehicle safety and control; this behaviour becomes more important when that surface is snow. The interaction of rubber and a snow surface is complex and a deeper understanding of both is needed in order to ...
openaire   +1 more source

Overcoming Challenges in 3D Printing of Polyolefins and Their Composites: A Review on Strategies for Improved Printability and Performance

Polymer Engineering &Science, EarlyView.
This review integrates the molecular fundamentals, key challenges, and mitigation strategies in polyolefin 3D printing, focusing on shrinkage, warpage, and adhesion control. It highlights material design approaches using recycled polyolefins and functional fillers to improve printability, mechanical properties, and sustainability in additive ...
Malik Hassan, Philip McMorran, Marwan Eid, Julia Blair, Amar K. Mohanty, Manjusri Misra   +5 more
wiley   +1 more source

The viscoelasticity of the rubber-ice interface determined by resonance shear measurement: influence of rubber <i>T</i> _g. [PDF]

Sci Technol Adv Mater
Stevens MC, Pallbo J, Kurihara K, Mizukami M.   +3 more
europepmc   +1 more source

Characteristics, properties and limitations of per‐ or polyfluoroalkyl substances (PFASs) and fluoropolymers

Polymer International, EarlyView.
An overview and categorization of man‐made per‐ or polyfluoroalkyl substances (PFASs) including low‐molar‐mass and high‐molar‐mass fluorochemicals, and their international regulations is presented. Though certain PFASs are toxic, bioaccumulative and cross the human cellular membranes, others, such as fluoropolymers, are safe, reliable and involved in ...
Bruno Améduri
wiley   +1 more source

Bioconversion and characterization of watermelon rind waste‐based microcrystalline cellulose: A green alternative to synthetic reinforcements

Polymer International, EarlyView.
Microcrystalline cellulose (MCC) was extracted from watermelon rind using acid hydrolysis. MCC can be efficiently used as reinforcement in biofilms and biocomposites. Abstract The increasing accumulation of agricultural waste from watermelon (Citrullus lanatus) represents a substantial environmental concern, particularly in view of the extensive ...
Indran Suyambulingam, Sunesh Narayanaperumal, Divya Divakaran, Nadir Ayrilmis, P Senthamaraikannan, Siva Avudaiappan, Yamuna Munusamy, H Jeevan Rao   +7 more
wiley   +1 more source

Friction of Rubber Rolls.

NIPPON GOMU KYOKAISHI, 1997
openaire   +2 more sources

Valorization of Poplar Wood Wastes Into 3D‐Printed Soya Oil‐Based Composites by Vat Photopolymerization for Interior Design

Journal of Polymer Science, EarlyView.
Bio‐based polymer composites were 3D printed by LCD vat photopolymerization using acrylate epoxidized soybean oil as the monomer and isobornyl methacrylate as the reactive diluent. Two different poplar powders derived from plywood processing waste were incorporated within the photocurable formulations.
Francesca Sacchi, Tiziano Uriel Monteu Cotto, Giovanna Colucci, Guido Callegari, Paolo Simeone, Daniela Bosia, Federica Bondioli, Massimo Messori   +7 more
wiley   +1 more source

Conjugated Polymers Engineered for Flexible/Stretchable Electronics

Journal of Polymer Science, EarlyView.
This review highlights glass transition temperature (Tg) as the central parameter linking molecular structure to device performance in conjugated polymers. By tuning backbone rigidity, side‐chain architecture, and dynamic bonding, Tg governs the balance between π–π stacking–enabled charge transport and mechanical compliance.
Yunchong Yang, Josh Bass, Weijia Yan, Ashwath Anand, Chunka Zhou, Jingjing Qiu   +5 more
wiley   +1 more source

Investigation of the Effect of Contact Seal Geometry on Frictional Moment in Ball Bearings. [PDF]

Materials (Basel)
Zmarzły P, Wrzochal M, Rębosz-Kurdek A.   +2 more
europepmc   +1 more source

Synthesis and Characterization of an Azido Nitrofurazanyl Ether: An Energy‐Rich Heterocyclic Plasticizer With a Low Glass Transition Temperature

Propellants, Explosives, Pyrotechnics, EarlyView.
ABSTRACT We report on the synthesis and characterization of 3‐(2‐(2‐azidoethoxy)ethoxy)‐4‐nitro‐1,2,5‐oxadiazole (NFPEG2N3), which is a liquid nitrofurazanyl ether that was designed to be an energy‐rich plasticizer for glycidyl azide polymer (GAP)‐ and nitrocellulose (NC)‐based formulations.
P. Lieber, A. Omlor, U. Schaller, T. M. Klapötke   +3 more
wiley   +1 more source