Results 1 to 10 of about 2,699,553 (122)
Inventions, 2023 The aim of this paper is to evaluate the corrosion rate expressed in material loss per unit of time and the surface properties of carbon steel type S235JR blasted with different types of materials (quartz, alumina, and red garnet with a particle size ...
Nicoleta Bogatu +6 more
doaj +4 more sources
Corrosion Behavior of S235JR Carbon Steel in 0.5 M HCl Solution During 24 Weeks
MetalsThis study aims to evaluate the corrosion behavior of and morphological changes in S235JR steel exposed to 0.5 M hydrochloric acid solution over a period of 24 weeks.
Alina Crina Mureșan +4 more
doaj +4 more sources
Interactions between C-steel and blended cement in concrete under radwaste repository conditions at 80 °C [PDF]
Scientific Reports, 2023 Deep geological repository is widely considered as the preferred solution for the final disposal of high-level radioactive waste. Investigation representative of the Hungarian disposal concept was conducted using mock-up diffusion cells to study the ...
Margit Fabian +3 more
doaj +2 more sources
Effect of Thermal Treatment and Erosion Aggressiveness on Resistance of S235JR Steel to Cavitation and Slurry. [PDF]
Materials (Basel), 2021 Krella AK +3 more
europepmc +2 more sources
Properties and Microstructure of Laser Welded Dissimilar Joints of TP347-HFG and S235JR Steels with Additional Material [PDF]
Archives of Metallurgy and Materials, 2020 Paper presents results of laser welding of dissimilar joints. Flange pipe joints of austenitic TP347-HFG and low carbon S235JR steels were performed. Possibility of laser girth welding of dissimilar joints was presented.
H. Danielewski +3 more
doaj +1 more source
Research and Development on Coatings and Paints for Geothermal Environments: A Review
Advanced Materials Technologies, Volume 8, Issue 18, September 25, 2023., 2023 Geothermal power production, by harnessing the natural heat in the earth's crust, provides clean energy, with year‐round availability. However, corrosion, erosion, and scaling of power plant components can hinder energy production. In his review paper, the first of its kind since 1980, a detailed overview of research studies on coatings developed to ...
Francesco Fanicchia +1 more
wiley +1 more source
Materials and Corrosion, Volume 74, Issue 8, Page 1148-1158, August 2023., 2023 Zinc flake coatings are compared using spectroelectrochemistry, accelerated corrosion and outdoor weathering tests. Chloride concentration, and its effect on the passive oxide, appears key to moderating the sacrificial zinc dissolution rate. We gained insight into the influence of the environment and zinc flake (alloy) used, paving the way for tailored
Florian Feldmann +3 more
wiley +1 more source
Oxygen‐Free Production—From Vision to Application
Advanced Engineering Materials, Volume 25, Issue 12, June 2023., 2023 Extremely low oxygen partial pressures can be obtained by adding small amounts of monosilane to an inert gas environment. The effects of such an environment on various production processes such as milling, compound casting, and thermal spraying are analyzed.
Lienhard Wegewitz +4 more
wiley +1 more source
Metals, 2022 This paper investigates the manipulation of chemical composition of a laser weld by dissimilar filler material and its effect on residual stress. The aim is to minimize residual stresses in the weld seam.
Fatma Akyel +5 more
doaj +1 more source
Extracting true stresses and strains from nominal stresses and strains in tensile testing
Strain, Volume 57, Issue 6, December 2021., 2021 Abstract Seemingly a simple task, the extraction of the flow curve (true stress vs. true plastic strain) from nominal stresses and strains in standard tensile testing still has its unsolved points. This study addresses two of them: (i) in materials without yield point phenomenon (or generally in the region of homogeneous plastic deformation), the true ...
Rainer Schwab, Anton Harter
wiley +1 more source