Results 51 to 60 of about 2,307 (213)

Correlation between SDAS and mechanical properties of Al–Si alloy made in Sand and Slag moulds

Journal of Materials Research and Technology, 2020
Investigations have been carried out to evaluate the correlations between microstructure and mechanical properties of cast products made by Ferro chrome (Fe-Cr) slag and Granulated Blast Furnace (GBF) slag moulds in tune with silica sand moulds.
Ravi Kanth Yajjala, Narasimha Murthy Inampudi, Babu Rao Jinugu   +2 more
doaj   +1 more source

Weak In‐Plane Ferromagnetism and Electronic Nematicity in the Distorted Triple‐Q Magnetic Phase of Co1/3TaS2

Advanced Materials, EarlyView.
Co1/3TaS2${\rm Co}_{1/3}{\rm TaS}_{2}$ hosts a triple‐Q noncoplanar antiferromagnetic state with coexisting Z3${\rm Z}_3$ electronic nematicity. We report rotational hysteresis observed in both magnetoresistance and magnetic torque, revealing strongly pinned in‐plane weak ferromagnetic moments in the triple‐Q phase and the magnetism‐driven nature of ...
Joonyoung Choi, Woonghee Cho, Pyeongjae Park, Woun Kang, Je‐Geun Park, Younjung Jo   +5 more
wiley   +1 more source

Effect of aluminum silicate fiber modification on crack-resistance of a ceramic mould [PDF]

China Foundry, 2012
To improve the crack-resistance of the mould for silica sol bonded quartz based ceramic mould casting, aluminum silicate fibers with the diameter ranging from 5 µm to 25 µm and the length about 1 mm were dispersed in the ceramic mould.
Jiang Yehua, Wang Zhao, Lu Dehong
doaj  

High Center‐of‐Mass, Multi‐Legged Soft Robots Powered by Geometrically Encoded Liquid Crystal Elastomer Arc Appendages

Advanced Materials, EarlyView.
Inspired by the octopus and the golden wheel spider, soft robots with liquid crystal elastomer arc fibers as appendages are fabricated to transcend surface constraints through an elevated center of mass and minimal contact footprints. By leveraging curvature‐encoded deformation‐recovery cycles, these robots exhibit contractile, torsional, and flexural ...
Jong Bin Kim, Antonio Proctor Martinez, Yaoye Hong, Ziyun Zhang, Kun‐Yu Wang, Shu Yang   +5 more
wiley   +1 more source

Enhanced Photocatalytic H2O2 Production on Terpyridine‐Based Acrylonitrile‐Linked Covalent Organic Frameworks with Asymmetric Localized Electron Distribution

Advanced Materials, EarlyView.
Asymmetric localized electron distribution has been optimized in covalent organic frameworks to enhance *O2 adsorption and facilitate charge transfer, boosting photocatalytic two‐electron transfer oxygen reduction toward H2O2 production from water and air.
Qinglan Zhao, Mengmeng Ce, Hengtao Lei, Tianyun Jin, Zhipeng Xie, Yushen Liu, Shengyi Yang, Xinwen Ou, Mohammad Farhadpour, Song‐Zhu Kure‐Chu, Xuan‐He Liu, Liang Zhang, Jimmy C. Yu   +12 more
wiley   +1 more source

A 3D‐Printed Blister Test Platform for Quantifying Biointerface Adhesion Mechanisms

Advanced Materials Interfaces, EarlyView.
A 3D‐printed blister platform enables energy‐resolved characterization of soft hydrogel–rigid interfaces. Integrating precision pressure control with hyperelastic modeling directly quantifies adhesion energy (G) and R‐curve toughening. Results reveal that modulating hydrogel concentration and surface roughness drives a tunable transition from cohesive ...
Yoontae Kim, Rahul Patil, Argyris K. Lazaris, Xinran Zhang, Stella Alimperti   +4 more
wiley   +1 more source

ASSESSMENT OF SURFACE FINISH AND DIMENSIONAL ACCURACY OF TOOLS MANUFACTURED BY METAL CASTING IN RAPID PROTOTYPING SAND MOULDS

South African Journal of Industrial Engineering, 2012
In this paper, an initial assessment of the quality parameters of the surface finish and dimensional accuracy of tools made by metal casting in rapid prototyping (RP) sand moulds is undertaken.
Nyembwe, K. , De Beer, D. J., Van der Walt, J. G., Bhero, S.   +3 more
doaj   +1 more source

Parallel Electrical Integration of Photo Bio Electrochemical Systems (photo‐BESs): Performance Gains and Load Dependency

Advanced Materials Technologies, EarlyView.
Parallel wiring of bioelectrochemical devices with conventional generators unexpectedly boosts output. A biophotovoltaic paired with a solar cell delivers up to 50% more power at low loads than their separate contributions; a plant microbial fuel cell shows similar current gains.
Valeria Marsaglia, Paolo Bombelli, Ingrid Paoletti, Ioannis A. Ieropoulos, Christopher J. Howe   +4 more
wiley   +1 more source

Investigation of Some Moulding Properties of a Nigerian Clay-Bonded Sand

Archives of Foundry Engineering, 2016
Moulding properties of Isasa River Sand bonded with Ipetumodu clay (Ife-North Local Government Area, Osun State, Nigeria) were investigated. American Foundry men Society (AFS) standard cylindrical specimens 50mm diameter and 50mm in height were prepared ...
Oke A.O., Omidiji B.V.
doaj   +1 more source

Micropillar‐Engineered Hybrid Adhesive Patch for Surface‐Conformable and Directional Adhesion

Advanced Materials Technologies, EarlyView.
This work presents a surface‐conformable hybrid adhesive integrating height‐optimized hexagonal micropillars with open‐rectangular cuts. The micropillars enhance rough‐surface contact and microscale crack arrest, while the cuts guide and reverse interfacial cracks for strong and directional adhesion. The multiscale architecture achieves robust pull‐off
Seongjin Park, Dong Kwan Kang, Haejin Bae, Ho‐Sup Jung, Hoon Eui Jeong   +4 more
wiley   +1 more source