Results 121 to 130 of about 267,692 (300)
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
Strategic maxillary second-molar extraction in Class II malocclusion
, 2009 Maxillary second-molar extraction in Class II malocclusion is a controversial issue in orthodontics. This treatment protocol is rigorous and not routine. In this case report, we present the orthodontic treatment of a patient with a Class II malocclusion,
HENRIQUES, Jose Fernando Castanha +4 more
core +1 more source
Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion
Advanced Engineering Materials, EarlyView.Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello +7 more
wiley +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
Treatment of second molar impaction
, 2018 Although the prevalence of second molar impaction is not very high, retention can be a real functional problem within the oral cavity, leading to a loss of posterior support and decreased masticatory potential.
L. Messica
core +1 more source
Laser‐Induced Graphene from Waste Almond Shells
Advanced Functional Materials, EarlyView.Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source
Second molar intrusion: Continuous arch or loop mechanics?
, 2018 Introduction: Our aim was to compare the load systems produced by rectangular loops and continuous arch mechanics on intrusion of a maxillary second molar.
Martins, Lidia Parsekian +7 more
core +1 more source
Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer
Advanced Functional Materials, EarlyView.Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero +12 more
wiley +1 more source
, 2014 In 2005 we reported the clinical findings of 100 patients who had mandibular third molars removed because of distal cervical caries in the mandibular second molar.
McArdle, LW +5 more
core +1 more source