Results 1 to 10 of about 2,709,951 (198)
Advanced Photocatalysts for CO2 Conversion by Severe Plastic Deformation (SPD). [PDF]
Materials (Basel), 2023 Excessive CO2 emission from fossil fuel usage has resulted in global warming and environmental crises. To solve this problem, the photocatalytic conversion of CO2 to CO or useful components is a new strategy that has received significant attention. The main challenge in this regard is exploring photocatalysts with high efficiency for CO2 photoreduction.
Akrami S, Ishihara T, Fuji M, Edalati K.
europepmc +4 more sources
Materials & Design, 2020 The emergence of shear inhomogeneity across grain boundaries during severe shear deformation in Cu at the micrometer length-scales is demonstrated through in situ imaging inside a scanning electron microscope.
Shan Gong, M. Ravi Shankar
doaj +1 more source
Semi-Continuous Equal-Channel Angular Extrusion and Rolling of AA5083 and AZ31 Alloys
Metals, 2019 This paper describes a new modification of equal-channel angular extrusion for the “pass-by-pass” semi-continuous (sc-ECAE) processing of lightweight alloys.
Vladimir Segal +4 more
doaj +1 more source
Severe Plastic Deformation of Nanostructured Cu-30%Zn Tubes at Increased Temperatures [PDF]
International Journal of Advanced Design and Manufacturing Technology, 2017 Severe plastic deformation (SPD) methods were developed for producing of metals and alloys with ultrafine grained (UFG) microstructures having high strength.
V. Tavakoli +3 more
doaj
Development of SPD continuous processes for strip and rod production
Metalurgija, 2010 Grain refinement upon the severe plastic deformation (SPD) at low temperatures (below the recrystallization temperature) and an unusual improvement the properties of such materials are shown reliably. However, the industrial application is limited due to
S. Dobatkin, J. Zrnik, Ilija Mamuzić
doaj
Advances in Materials Science and Engineering, 2014 Severe plastic deformation (SPD) has been widely employed to refine the grain size of Mg alloys, with the main objective to improve the strength and ductility of Mg alloys, since the well-known Hall-Petch equation suggests that a decreased grain size ...
Jinbao Lin +4 more
doaj +1 more source
The Temperature Effect on Severely Deformed Aluminium by High Pressure Torsion
The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2009 The process of deforming materials started to attract the interest of the researchers after the development of the severe plastic deformation techniques.
Carmela GURAU +5 more
doaj
Evaluating the flow processes in ultrafine-grained materials at elevated temperatures
Materials Research, 2013 When polycrystalline materials are tested in tension at elevated temperatures, the flow mechanisms depend upon various parameters including the temperature of testing, the applied stress and the material grain size.
Megumi Kawasaki, Terence G. Langdon
doaj
Formation of ultrafine-grained (UFG) structure and mechanical properties by severe plastic deformation (SPD) [PDF]
Metalurgija, 2008 Commercial pure cooper (99,9% Cu) was deformed by equal channel angular pressing (ECAP) using up to 10 passes, route C. The evolution of microstructure and fracture character were observed by OM, SEM and TEM. The mean grain size decreased with increasing
M. Besterci +4 more
doaj
Grain Growth during Annealing of Ultrafine-Grained and Nanomaterials
Успехи физики металловUltrafine-grained metals and alloys with a submicrocrystalline structure in some cases demonstrate a set of unique properties, for example, high strength and hardness, low-temperature superplasticity at high strain rates, and improved electrical and ...
I.E. Volokitina, T.D. Fedorova, and D.N. Lavrinyuk
doaj +1 more source