Results 61 to 70 of about 370 (109)
steel research international, Volume 97, Issue 3, Page 1201-1225, March 2026.This review investigates the processing‐microstructure‐property relationships in ferritic stainless steels (FSSs). It highlights advances in deformation behavior, heat treatments, surface modifications, and alloying effects. Theoretical models, including Johnson‐Mehl‐Avrami‐Kolmogorov, Arrhenius, nucleation theory, and diffusion theories, are discussed
Shahab Bazri +4 more
wiley +1 more source
Ten years of severe plastic deformation (SPD) in Iran, part II: accumulative roll bonding (ARB)
, 2018 The present paper is the second part of a previously published overview entitled “ten years of severe plastic deformation (SPD) in Iran”. Part I concentrates on the equal channel angular pressing (ECAP). In this part, the focus is on the accumulative roll bonding (ARB) because, currently, Iran is ranked the first in the world by the total number of ...
Reihanian, M +4 more
openaire +3 more sources
The Temperature Effect on Severely Deformed Aluminium by High Pressure Torsion
The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2009 The process of deforming materials started to attract the interest of the researchers after the development of the severe plastic deformation techniques.
Carmela GURAU +5 more
doaj
Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy
Advanced Engineering Materials, Volume 28, Issue 4, 18 February 2026.An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley +1 more source
Advances in Materials Science and Engineering, 2014 Severe plastic deformation (SPD) has been widely employed to refine the grain size of Mg alloys, with the main objective to improve the strength and ductility of Mg alloys, since the well-known Hall-Petch equation suggests that a decreased grain size ...
Jinbao Lin +4 more
doaj +1 more source
Evaluating the flow processes in ultrafine-grained materials at elevated temperatures
Materials Research, 2013 When polycrystalline materials are tested in tension at elevated temperatures, the flow mechanisms depend upon various parameters including the temperature of testing, the applied stress and the material grain size.
Megumi Kawasaki, Terence G. Langdon
doaj
Formation of ultrafine-grained (UFG) structure and mechanical properties by severe plastic deformation (SPD) [PDF]
Metalurgija, 2008 Commercial pure cooper (99,9% Cu) was deformed by equal channel angular pressing (ECAP) using up to 10 passes, route C. The evolution of microstructure and fracture character were observed by OM, SEM and TEM. The mean grain size decreased with increasing
M. Besterci +4 more
doaj
Metalurgija, 2008 Trgovački čisti bakar (99,9%) deformiran je kanalnim kutnim prešanjem (KKP) do 10 provlaka-putanje. C. Razvitak mikrostrukture i karakter loma praćeno je sa OM, SEM i TEM. Veličina zrna se smanjuje povećanjem deformacije poslije 10 provlaka na 100-300 nm.
M. Besterci +4 more
openaire +4 more sources
Grain Growth during Annealing of Ultrafine-Grained and Nanomaterials
Успехи физики металловUltrafine-grained metals and alloys with a submicrocrystalline structure in some cases demonstrate a set of unique properties, for example, high strength and hardness, low-temperature superplasticity at high strain rates, and improved electrical and ...
I.E. Volokitina, T.D. Fedorova, and D.N. Lavrinyuk
doaj +1 more source
Metals, 2019 It has been found that a high electrical conductivity of 63.1%, the International Annealed Copper Standard (IACS), and high mechanical properties are achieved by the initial aluminum alloy after undergoing four cycles of the severe plastic deformation ...
Ilya A. Zhukov +7 more
doaj +1 more source