Results 271 to 280 of about 160,905 (311)
Some of the next articles are maybe not open access.
Investigating shear performance of PMCS
2023Understanding the shear performance of polymer matrix composites (PMCs) using a multiscale methodology requires novel in situ experimental techniques at each length scale. One limitation of the multiscale paradigm is inadequate experimentation at the microscale. In addition, limited investigation exists at the mesoscale to understand progressive damage
Flores, Mark +6 more
openaire +1 more source
Flexural and shear performance of HFRC beams
Materials Today: Proceedings, 2021Abstract This paper describes the load bearing capacity prediction of two different types of fibres in Reinforced Concrete (RC) beams exposed to bending loads. A two-point test in a loading frame was conducted under static loading to examine the flexural and shear performance of Hybrid Fibre Reinforced Concrete (HFRC) beams in the preparation of ...
M. Vinod Kumar +4 more
openaire +1 more source
Performance Evaluation of Composite Shear Wall
2020Shear wall systems are one of the most commonly used lateral load resisting systems in high-rise buildings. Composite shear walls are a combination of steel and concrete sections, which unites the advantages of steel and concrete shear wall systems. The encased composite shear wall system studied here consists of stiffened steel sheets, shear studs ...
S. Sariganath, Milu Mary Jacob
openaire +1 more source
Analysis and performance of a shear-wave magnetometer
Sensors and Actuators A: Physical, 1993Abstract A detailed analysis of the response of a shear-wave magnetometer to applied magnetic field and temperature is presented. This facilitates the identification of dominant sources of noise. It is shown both theoretically and experimentally that a scheme of phase feedback significantly reduces the effect of temperature on the system.
C.F. Kilby, P.T. Squire, S.N.M. Willcock
openaire +1 more source
Foamed bitumen mixes = shear performance?
International Journal of Pavement Engineering, 2007Road rehabilitation technology is currently under the global spotlight. Considering that cold bituminous binders, e.g. emulsion and foamed bitumen, have become more commonly used in cold recycling operations, there is a need to understand the performance properties of these materials.
Jenkins KJ, Long F.M., Ebels LJ
openaire +1 more source
MIXING PERFORMANCE OF HIGH SHEAR IMPELLERS
Chemical Engineering Communications, 1982Abstract The characteristics of a high shear impeller, the TURBON mixer, have been extensively investigated. The correlating equation for power requirement of this mixer with three types of impeller has been obtained for a liquid single phase and a gas-liquid two-phase system.
KAKUJI TOJO, KEI MIYANAMI
openaire +1 more source
Performance of Embedded Bolt Shear Connectors
Structural Engineering International, 2020A laboratory research program carried out at the University of Waterloo featured the testing of three large-scale steel-concrete composite beam specimens with embedded bolt shear connectors.
Sjaarda, Matthew +2 more
openaire +2 more sources
Performance of Profiled Concrete Shear Panels
Journal of Structural Engineering, 1998This paper describes the behavior of profiled concrete shear panels that may be used as core walls in framed construction.
K. M. Anwar Hossain, Howard D. Wright
openaire +1 more source
Performance and Strength of Welded Shear Studs
Composite Construction in Steel and Concrete IV, 2002The behavior and strength of welded shear studs are subjects of ongoing study. A description of the formulation of the American Institute of Steel Construction specification provisions for the strength of shear studs is given. The behavior of shear studs as influenced by friction, position of studs in steel deck and stud properties is described.
Michelle Rambo-Roddenberry +3 more
openaire +1 more source
The Performance of Epoxy-Coated Shear Reinforcement
ACI Structural Journal, 1996This paper examines the performance of epoxy-coated stirrups in reinforced concrete beams under bending and shear. A review of previous studies in bond and detailing of stirrups is provided. The results of an experimental program are described. From these results, several conclusions are reached, supported by ultimate failure load, deflection, stirrup ...
openaire +1 more source