Results 21 to 30 of about 91,301 (310)
Effect of initial temper on mechanical properties of creep-aged Al-Cu-Li alloy AA2050
MATEC Web of Conferences, 2018 The evolution of mechanical properties of a third generation Al-Cu-Li alloy, AA2050, with different initial tempers (T34 and as-quenched (WQ)) during creep-ageing has been investigated and analysed in this study. A set of creep-ageing tests under 150 MPa
Li Yong +5 more
doaj +1 more source
The effect of thermal spraying on the forming performance of incremental sheet forming
Journal of Materials Research and Technology, 2021 Abstrac: In order to reduce the manufacturing cycle and improve the forming performance of the incremental sheet forming (ISF) process, a hybrid manufacturing process that combines thermal spraying and incremental forming process was firstly proposed ...
Yuanyu Liu +4 more
doaj +1 more source
A Constitutive Friction Law for Sheet-Bulk Metal Forming
Tribology Online, 2016 Friction has a significant effect on metal forming both in economic and technical terms. This is especially true for sheet-bulk metal forming, which is a combination of bulk metal forming and sheet metal forming.
Florian Beyer, Kai Willner
doaj +1 more source
Electrohydraulic sheet metal forming with flexible tools
MATEC Web of Conferences, 2018 In cold metal forming usually a die and a punch are required to form sheet metal in the desired shape. These two parts of the tool need to be produced of hardened materials in high precision.
Pegel Holger +4 more
doaj +1 more source
The Use of Non-Edible Green Oils to Lubricate DC04 Steel Sheets in Sheet Metal Forming Process
Lubricants, 2022 Lubrication is a basic and relatively effective way to reduce friction in sheet metal forming operations. The drive to eliminate synthetic and mineral oils, which are difficult to recycle, from the manufacturing process has opened up opportunities for ...
Tomasz Trzepieciński +2 more
doaj +1 more source
TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series A, 1989 The forming limit of sheet metals is examined in terms of the uniqueness of the solution. There are two cases indicating multiplicity, one is statically admissible and another is kinematically admissible. The multiplicities are considered to correspond to plastic instabilities.
openaire +2 more sources
Springback of thick sheet AHSS subject to bending under tension [PDF]
, 2012 Lien vers la version éditeur : http://www.sciencedirect.com/science/article/pii/S0020740312000677The springback behavior of four advanced high-strength sheet steels (Dual-Phase, TRIP, ferrite-bainite) with thicknesses ranging from 1.2 to 4 mm was ...
BALAN, Tudor +2 more
core +1 more source
EXPERIMENTAL EVALUATION OF DRAW BEAD COEFFICIENT OF FRICTION
Acta Metallurgica Slovaca, 2017 In this paper the results of both friction coefficient and springback testing using a drawbead test are presented. Deep drawing quality steel sheet (DC04 according to EN 10130:2009 standard) was used as the test material.
Tomasz Trzepiecinski +2 more
doaj +1 more source
Forming Of Spherical Titanium Cups From Circular Blanks With Cutouts On The Perimeter
Archives of Metallurgy and Materials, 2015 Despite substantial demand for drawn parts made of high-strength sheet metal (including titanium alloys) observed in the modern industry, particularly automotive and aviation, their application remains insignificant.
Lacki P. +3 more
doaj +1 more source
Virtual Sensor-Based Geometry Prediction of Complex Sheet Metal Parts Formed by Robotic Rollforming
Robotics, 2023 Sheet metal parts can often replace milled components, strongly improving the buy-to-fly ratio in the aeronautical sector. However, the sheet metal forming of complex parts traditionally requires expensive tooling, which is usually prohibitive for low ...
Tina Abdolmohammadi +5 more
doaj +1 more source