Results 81 to 90 of about 91,301 (310)

Analysis of Material Deformation and Wrinkling Failure in Conventional Metal Spinning Process [PDF]

, 2012
Sheet metal spinning is one of the metal forming processes, where a flat metal blank is rotated at a high speed and formed into an axisymmetric part by a roller which gradually forces the blank onto a mandrel, bearing the final shape of the spun part ...
WANG, LIN
core  

New approaches in incremental sheet forming with a robot system for an industrial work-piece

, 2022
S.923-928This paper introduces new results of the single point incremental forming process of an industrial sheet metal component. Incremental sheet forming (ISF) is an innovative and compared to conventional forming technologies which does require ...
Verl, Alexander, Puzik, Arnold
core  

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Strain localization analysis using a multiscale model [PDF]

, 2007
In order to analyze the formability of steels in sheet metal forming, a ductility loss criterion is coupled with a multiscale model. The behavior at the mesoscopic (grain) scale is modeled by a large strain micromechanical constitutive law, which is then
LEMOINE, Xavier, BERVEILLER, Marcel, ABED-MERAIM, Farid, FRANZ, Gérald, BEN ZINEB, Tarak   +4 more
core   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Review of approximate analyses of sheet forming processes

, 2011
Approximate models are often used for the following purposes: in on-line control systems of metal forming processes where calculation speed is critical; to obtain quick, quantitative information on the magnitude of the main variables in the early stages ...
Rolfe, Bernard F., Weiss, Matthias, Matthias Weiss, Bernard Rolfe, Yang, Chunhui (R16973), Peter Hodgson, Souza, Tim de, Hodgson, Peter D., Chunhui Yang, Tim de Souza   +9 more
core   +1 more source

Biomass Native Structure Into Functional Carbon‐Based Catalysts for Fenton‐Like Reactions

Advanced Functional Materials, EarlyView.
This study indicates that eight biomasses with 2D flaky and 1D acicular structures influence surface O types, morphology, defects, N doping, sp2 C, and Co nanoparticles loading in three series of carbon, N‐doped carbon, and cobalt/graphitic carbon. This work identifies how these structural factors impact catalytic pathways, enhancing selective electron
Wenjie Tian, Jingkai Lin, Zhihao Tian, Selusiwe Ncube, Huayang Zhang, Emiliano Cortés, Hongqi Sun, Shaobin Wang   +7 more
wiley   +1 more source

Composites of Shellac and Silver Nanowires as Flexible, Biobased, and Corrosion‐Resistant Transparent Conductive Electrodes

Advanced Functional Materials, EarlyView.
Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein, Tiago Carneiro Gomes, Eliza Ng, Simon Rondeau‐Gagné, Tricia Breen Carmichael   +4 more
wiley   +1 more source

Capabilities of Using Fem in Sheet-Metal Forming

Archives of Metallurgy and Materials, 2016
The aim of this study was to determine and select boundary conditions of modeling and FEM simulation for plastic processing on the example of sheet-metal forming. For sheet-metal deformation analysis, Deform 3D has been used.
Korga S., Duda A., Ciekanowski Z.
doaj   +1 more source