Results 131 to 140 of about 1,594,617 (281)
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source