Results 111 to 120 of about 4,018 (263)

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

Advanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang, Peter Zalar, Vishva Bhate, Takeo Furukawa, Hidekazu Kodama, Yijun Liu, Yuanyuan Zhou, Chuang Hou, Siyuan Liu, Naoji Matsuhisa   +9 more
wiley   +1 more source

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

Advanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja, Mikko Kokkonen, Niina Halonen, Sami Myllymäki, Umair Rafique, Mandeep Singh, Ossi Laitinen, Heli Jantunen, Kristiina Oksman, Henrikki Liimatainen   +9 more
wiley   +1 more source

High Throughput Aerosol Jet Printing to Operationalize High Aspect Ratio Patterning

Advanced Materials Technologies, EarlyView.
High‐throughput aerosol jet printing poses distinct limiting mechanisms to the printing process. These include rapidly changing ink chemistries, atomization instabilities, and liquid‐phase spreading. The combination of in‐line heating, process monitoring, and traditional optimization procedures enables rapid printing of high‐aspect‐ratio structures ...
Bella I. Guyll, Md Mahdi Ul Ishtiaque, Md Ramjan Ali, Todd A. Kingston, Ethan B. Secor   +4 more
wiley   +1 more source

Post-Fabrication Phase Correction of SOI 4 × 4 MMI-Based 90° Optical Hybrids via Femtosecond-Laser Trimming. [PDF]

Nanophotonics
Du J, Bao X, Lin J, Chen X, Jiang W, Zhang B, Xiong Y, Li W, Zhou L.   +8 more
europepmc   +1 more source

Aerosol Jet Printing of Benzocyclobutene as a Thermally Stable, Low‐Loss Dielectric for Multilayer Microwave Electronics

Advanced Materials Technologies, EarlyView.
Multilayer aerosol jet printed components with a low‐loss, thermally stable dielectric are demonstrated using benzocyclobutene. Ink formulation and in‐line droplet evaporation control support high‐quality, versatile, and stable printing performance. A specialized measurement for low‐loss materials reveals promising microwave properties, which, combined
Md Ramjan Ali, Trent Moritz, Mohammad Tayeb Al Qaseer, Ethan B. Secor   +3 more
wiley   +1 more source

Liquid‐Crystal‐Based Reconfigurable Intelligent Surface for 7 GHz Mobile Communication

Advanced Materials Technologies, EarlyView.
The glass‐based liquid‐crystal reconfigurable intelligent surface (LC‐RIS) integrates active‐matrix driving and blind‐greedy phase optimization within a 5G‐NR OFDM framework. This enables continuously tunable and autonomous enhancement of wireless coverage. Leveraging the transparency and manufacturability of liquid crystal panels, it is ideally suited
Tien‐Lun Ting, Yuh‐Chyi Chang, Yi‐Chan Hung, Cheng‐Yuan Hsiao, Chao‐Kai Wen, Tsung‐Hsien Lin   +5 more
wiley   +1 more source

Photoluminescence Reshaping via Structural Confinement and Local Density of Optical States Control in Ir(III)‐Doped Biodegradable Metasurfaces

Advanced Materials Technologies, EarlyView.
Phosphorescent biodegradable metasurface showing vibronic selection and spectral photoluminescence narrowing. Anti‐correlation between experimental LDOS and measured lifetimes. ABSTRACT Metasurfaces incorporating phosphorescent emitters offer a route to engineer radiative and vibronic processes beyond chemical design.
Vincenzo Caligiuri, Andrea Smeriglio, Svetlana Siprova, Olga Favale, Francesca Leone, Roberto Termine, Debora Policastro, Alessandra Crispini, Attilio Golemme, Nicolas Godbert, Iolinda Aiello, Antonio De Luca   +11 more
wiley   +1 more source

Characterization of Silicon-Membrane TES Microcalorimeters for Large-Format X-ray Spectrometers with Integrated Microwave SQUID Readout. [PDF]

IEEE Trans Appl Supercond
Roy A, Singh R, Weber JC, Doriese WB, Gard J, Keller MW, Mates JAB, Morgan KM, Ortiz NJ, Swetz DS, Schmidt DR, Ullom JN, Jahrman EP, Allison TC, Jamnuch S, Vinson J, Titus CJ, Jaye C, Fischer DA, O'Neil GC.   +19 more
europepmc   +1 more source

Recent Advances in Transparent Microelectrode Device Architecture and Fabrication Strategies for Biomedical Applications

Advanced Materials Technologies, EarlyView.
Transparent microelectrode arrays enable simultaneous optical and electrical electrophysiology with high spatiotemporal resolution, allowing multimodal observations of dynamic biological systems. Advances in materials and device architectures improve device performance by addressing key trade‐offs between optical transparency, impedance, and ...
Michael Abraham Listyawan, Tran Bach Dang, Chi Cong Nguyen, Yee Lap Pong, Tianruo Guo, Thanh Nho Do, Hoang‐Phuong Phan   +6 more
wiley   +1 more source

Spatially Configurable Conformal Sensor Integration on an Ultra‐Fine Metallic Needle for Minimally Invasive Deep‐Tissue Oxygen Monitoring

Advanced Materials Technologies, EarlyView.
A multi‐point oxygen‐sensing ultra‐fine needle (MO‐UFN) is developed by conformally integrating a lithographically patterned flexible electrochemical sensor array onto a clinical acupuncture needle. The platform preserves an approximately 0.3 mm diameter while enabling spatially resolved oxygen profiling along the insertion pathway.
Yeju Seo, Jaeho Park, Yongrok Jeong, Ji‐Hwan Ha, Junseong Ahn, Jimin Gu, Su A Park, Ilwoo Jun, Kichul Lee, Inkyu Park   +9 more
wiley   +1 more source